Bedienungsanleitung Makita DTR180 (Seite 16 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691779

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

16 ENGLISH

Tying work

CAUTION: Before inserting the battery car-

tridge, be sure to release your ngers from the

switch trigger and lock the trigger. If you insert

the battery cartridge while the switch trigger is being

pulled, it may cause an accident if the wire tying

process is accidentally carried out.

CAUTION: When you turn the power on, never

bring your limbs or face close to the binding or

rotating parts of the tool tip. Otherwise, you may

beinjured.

CAUTION: When the power is turned on,

never touch the binding or rotating parts of the

tool tip.Otherwise,youmaybeinjured.

►Fig.23

Preparation before work

1. Make sure that the battery cartridge is removed

and the trigger is locked.

2. Insert the battery cartridge into the tool, and turn

the power on. When you turn the power on, the wire is

cut automatically.

NOTICE: Make sure that the tying mode lamp

lights up when the power is turned on. If it does

not light up, recharge the battery.

3. Release the trigger lock.

►Fig.24: 1. Trigger-lock button 2. Switch trigger

3. Power button 4. Tying mode lamp

Single actuation mode

1. Push the arm securely against the tying point.

Push the tool vertically against the rebars, and press

the arm against the point where the rebars cross at a

45-degree angle.

►Fig.25

2. Pull the switch trigger once.

3. The wire is fed and cut automatically.

4. The hook holds and twists the wire, then returns to

the original position after the wires have been tied.

►Fig.26

5. After tying, exercise care not to hook the arm on

the rebars and pull the tool up.

CAUTION: If the wire has clung to the binding

part of the tool tip, turn the power of the tool off.

Lock the trigger, remove the battery cartridge,

and remove the wire using tools such as nippers

or pliers.

►Fig.27

Continuous actuation mode

1. Switch the tool mode from the single actuation

mode to the continuous actuation mode using the mode

switching button.

►Fig.28: 1. Mode switching button

2. Release the trigger lock.

3. While pulling the switch trigger, push the tool

vertically against the rebars, and press the arm against

the point where the rebars cross at a 45-degree angle.

Pressthecontactplatermlyagainstthetyingpoint.

The wire will be tied.

►Fig.29: 1. Contact plate

4. After tying, exercise care not to hook the arm on

the rebars and pull the tool up.

►Fig.30

Cautions on working

• If you move the arm from the tying position during

the wire tying process, the wire will get stuck on

the hook, which may lead to incorrect tying.

• Keep pressing the tool against the rebars until the

wire tying process is completed.

• Do not move to the next tying point until the cur-

rent wire tying process is completed.

• The tool tip rotating part (hook) twists the wire

duringthewiretyingprocess.Holdthegriprmly

so that your body is not pulled by the tool.

• Do not touch the wires during the wire tying

process.

• If you are repeating the wire tying processes in

thesingleactuationmode,fullyreleaseyournger

from the switch trigger. Then, continue to operate

the switch trigger.

• If you pull the switch trigger when there is no tie

wire left, an error is displayed. Replace with a new

tie wire and restart the tool.

Tying tips

• Tilt the tool at a 45° angle to the crossed rebars,

andtiealternatelyasshowninthegure.

►Fig.31

• Avoid strumous sections of rebars.

►Fig.32

• Iftyingstrengthisinsufcient,changethetying

orientation and perform tying twice so that tying

strength increases.

►Fig.33

NOTICE: When you make the second tie, bend

the tail of the rst tie before making the second

tie. Otherwise, the wire may be repelled a second

time. It may cling to the tool tip, and the hook may be

damaged.

Replacing the tie wires

CAUTION: When you replace the wire, be sure

to turn the power off, lock the trigger, and remove

the battery cartridge. Failure to do so may cause an

accident.

1. When wire has been used up, an error tone will

sound and error "1" will be displayed.

2. Lock the trigger, turn the power off, and remove

the battery cartridge.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTR180 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info