Bedienungsanleitung Makita DTS141 (Seite 7 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600212

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

NOTE:

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

Switch action (Fig. 3)

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

NOTE:

• The tool automatically stops if you keep pulling the

switch trigger for about 360 seconds.

Lighting up the front lamp (Fig. 4 & 5)

CAUTION:

• Do not look in the light or see the source of light

directly.

To turn on the lamp status, press the button for few

seconds. To turn off the lamp status, press the button

for few seconds again.

With the lamp status ON, pull the switch trigger to turn on

the lamp. To turn off, release it. The lamp goes out

approximately 10 seconds after releasing the switch

trigger.

With the lamp status OFF, the lamp will not turn on even

if the trigger is pulled.

NOTE:

• To confirm the lamp status, pull the trigger. When the

lamp lights up by pulling the switch trigger, the lamp

status is ON. When the lamp does not come on, the

lamp status is OFF.

• While pulling the switch trigger, the lamp status cannot

be changed.

• For approximately 10 seconds after releasing the

switch trigger, the lamp status can be changed.

Reversing switch action (Fig. 6)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for

counterclockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

Characteristics of Cordless Oil-impulse Driver

The Makita Cordless Oil-impulse Driver is a hydraulically

operated impact tool using oil viscosity to produce

impacts. Since oil viscosity changes with the

temperature, be aware of the following two points when

operating the tool.

1. Avoid using the tool below –10°C (14°F) of

temperature. When the tool temperature goes down

below the degrees, this may cause damage to the

motor of tool due to poor impulse.

2. When the tool becomes too hot, it may take longer to

set screws.

3. The tool can overheat, causing a failure or hand

burn if you operate it continuously for long hours. Let

the tool cool off for more than 30 minutes before

changing batteries during a long, continuous job.

Changing the impact force (Fig. 7)

015147

Impact force grade

displayed on panel

Maximum blows

Application Work

DTS131 DTS141

Hard

2,500

(min

–1

)

2,700

(min

–1

)

Tightening when force and

speed are desired.

Tightening in underwork

material / Tightening long

screws.

Medium

2,200

(min

–1

)

2,200

(min

–1

)

Tightening when a good

finishing is needed.

Tightening in the finishing

board, plaster board.

Soft

1,400

(min

–1

)

1,400

(min

–1

)

Tightening when excessive

tightening need to be avoided

because of potentially

clogged female screw and

broken or damaged screw

head.

Tightening sash screw/

Tightening small screws such

as M6.

Tightening bolt up to M8.

T mode

1,400

(min

–1

)

1,400

(min

–1

)

Tightening when speed and

good finishing are needed.

Tightening when speed and

good finishing are needed.

Tightening bolt up to M8.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTS141 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info