Bedienungsanleitung Makita DTS141 (Seite 9 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600212

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

• When it is difficult to insert the bit, pull the sleeve and

insert it into the sleeve as far as it will go.

• After inserting the bit, make sure that it is firmly

secured. If it comes out, do not use it.

Hook (Fig. 12)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool

housing on either side and then secure it with a screw. To

remove, loosen the screw and then take it out.

OPERATION (Fig. 13 & 14)

CAUTION:

• Never obstruct the air vents on the side of the tool for

cooling down oil unit and motor during operation.

Failure to do so may cause the tool excessive heat and

damage.

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. The relation between

fastening torque and fastening time is shown in the

figures. (Fig. 15 & 16)

Hold the tool firmly and place the point of the driver bit in

the screw head. Apply forward pressure to the tool to the

extent that the bit will not slip off the screw and turn the

tool on to start operation.

NOTE:

• Use the proper bit for the head of the screw/bolt that

you wish to use.

• Choose a proper impact force and carefully adjust

pressure on the switch trigger so that the screw is not

damaged.

• Hold the tool pointed straight at the screw.

• For tightening bolt, select the soft or T mode impact

force grade.

• If the impact force is too strong, you tighten the screw

for a time longer than shown in the figures, the screw or

the point of the driver bit may be overstressed,

stripped, damaged, etc. Before starting your job,

always perform a test operation to determine the

proper fastening time for your screw.

The fastening torque is affected by a wide variety of

factors including the following. After fastening, always

check the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening

torque will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket bit

will cause a reduction in the fastening torque.

3. Bolt

• Even though the torque coefficient and the class of

bolt are the same, the proper fastening torque will

differ according to the diameter of bolt.

• Even though the diameters of bolts are the same,

the proper fastening torque will differ according to

the torque coefficient, the class of bolt and the bolt

length.

4. The manner of holding the tool or the material of

driving position to be fastened will affect the torque.

5. Operating the tool at low speed will cause a

reduction in the fastening torque.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance except for the

following troubleshooting related to the light.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

•Screw bits

• Socket bits

•Hook

• Plastic carrying case

• Makita genuine battery and charger

• Bit-piece

• Battery protector

• Tool hanger

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ from

country to country.

ENG905-1

Noise

The typical A-weighted noise level determined according

to EN60745:

(In soft impact force grade)

Sound pressure level (L

): 77 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

(In soft impact force grade)

Work mode: impact tightening of fasteners of the

maximum capacity of the tool

Vibration emission (a

): 7.0 m/s

Uncertainty (K): 1.5 m/s

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTS141 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info