Bedienungsanleitung Makita DTW280 (Seite 7 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599995

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Indicating the remaining battery capacity (Fig. 3)

When you pull the switch trigger, the LED display shows

the remaining battery capacity.

The remaining battery capacity is shown as the following

table.

012273

NOTE:

• When the LED display goes off, the tool is turned off to

save the battery power. To check the remaining battery

capacity, slightly pull the switch trigger.

• The LED display goes off approximately one minute

after releasing the switch trigger.

• When the tool is overheated, the light flashes for one

minute, and then the LED display goes off. In this case,

cool down the tool before operating again.

• When the LED display lights up and the tool stops even

with a recharged battery cartridge, cool down the tool

fully. If the status will not change, stop using and have

the tool repaired by a Makita local service center.

Switch action (Fig. 4)

CAUTION:

• Before installing the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Lighting up the front lamp (Fig. 5 & 6)

CAUTION:

• Do not look in the light or see the source of light

directly.

To turn on the lamp status, press the button for one

second. To turn off the lamp status, press the button

for one second again.

With the lamp status ON, pull the switch trigger to turn on

the lamp. To turn off, release it. The lamp goes out

approximately 10 seconds after releasing the switch trig-

ger.

With the lamp status OFF, the lamp does not turn on

even if pulling the trigger.

NOTE:

• To confirm the lamp status, pull the trigger. When the

lamp lights up by pulling the switch trigger, the lamp

status is ON. When the lamp does not come on, the

lamp status is OFF.

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

• While pulling the switch trigger, the lamp status cannot

be changed.

• For approximately 10 seconds after releasing the

switch trigger, the lamp status can be changed.

Reversing switch action (Fig. 7)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for counter-

clockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

LED indicator status Remaining battery capacity

About 50% or more

About 20% – 50%

About less than 20%

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTW280 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info