Bedienungsanleitung Makita DTW280 (Seite 8 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599995

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Changing the impact force (Fig. 8)

014829

You can change the impact in three steps: hard, medium

and soft mode.

This allows a tightening suitable to the work.

Every time the button is pressed, the number of

blows changes in three steps.

For approximately one minute after releasing the switch

trigger, the impact force can be changed.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Selecting correct socket

Always use the correct size socket for bolts and nuts. An

incorrect size socket will result in inaccurate and incon-

sistent fastening torque and/or damage to the bolt or nut.

Installing or removing socket (Fig. 9 & 10)

For socket without O-ring and pin

Align the hole in the side of the socket with the detent pin

on the square drive and push the socket onto the square

drive until it locks into place. Tap it lightly if required.

To remove the socket, simply pull it off.

For socket with O-ring and pin

Move the O-ring out of the groove in the socket and

remove the pin from the socket. Fit the socket onto the

square drive so that the hole in the socket is aligned with

the hole in the square drive. Insert the pin through the

hole in the socket and square drive. Then return the O-

ring to the original position in the socket groove to retain

the pin. To remove the socket, follow the installation pro-

cedures in reverse.

Hook (Fig. 11)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool hous-

ing on either side and then secure it with a screw. To

remove, loosen the screw and then take it out.

OPERATION

CAUTION:

• Always insert the battery cartridge all the way until it

locks in place. If you can see the red part on the upper

side of the button, it is not locked completely. Insert it

fully until the red part cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to you or

someone around you.

Hold the tool firmly and place the socket over the bolt or

nut. Turn the tool on and fasten for the proper fastening

time. (Fig. 12)

The proper fastening torque may differ depending upon

the kind or size of the bolt, the material of the workpiece

to be fastened, etc. The relation between fastening

torque and fastening time is shown in the figures.

Model DTW280 (Fig. 13 & 14)

Model DTW281 (Fig. 15 & 16)

NOTE:

• Hold the tool pointed straight at the bolt or nut.

• Excessive fastening torque may damage the bolt/nut or

socket. Before starting your job, always perform a test

operation to determine the proper fastening time for

your bolt or nut.

• If the tool is operated continuously until the battery car-

tridge has discharged, allow the tool to rest for 15 min-

utes before proceeding with a fresh battery cartridge.

The fastening torque is affected by a wide variety of fac-

tors including the following. After fastening, always check

the torque with a torque wrench.

Impact force grade

displayed on panel

Maximum blows Application Work

Hard

3,500

(min

–1

)

Tightening when force and

speed are desired.

Assembling the steel frame.

Medium

2,600

(min

–1

)

Tightening when you need good

controlled power.

Assembling or disassembling

scaffolds or framework.

Soft

1,800

(min

–1

)

Tightening when you need fine

adjustment with small diameter

bolt.

Assembling the furniture.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTW280 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info