Bedienungsanleitung Makita DTW285 (Seite 7 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

657985

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

7 ENGLISH

NOTE:WhentheLEDdisplaygoesoff,thetoolis

turnedofftosavethebatterypower.Tocheckthe

remaining battery capacity, slightly pull the switch

trigger.

NOTE:TheLEDdisplaygoesoffapproximatelyone

minute after releasing the switch trigger.

NOTE:WhentheLEDdisplaylightsupandthetool

stops even with a recharged battery cartridge, cool

down the tool fully. If the status will not change, stop

using and have the tool repaired by a Makita local

service center.

NOTE:Whenthetoolisoverheated,thelightashes

foroneminute,andthentheLEDdisplaygoesoff.In

this case, cool down the tool before operating again.

Switch action

►Fig.5: 1. Switch trigger

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

Tostartthetool,simplypulltheswitchtrigger.Tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

NOTE:Thetoolautomaticallystopswhenyoukeep

pulling the switch trigger for 3 minutes.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

►Fig.6: 1. Lamp

►Fig.7: 1. Button

Toturnonthelampstatus,pressthebutton

for

onesecond.Toturnoffthelampstatus,pressthebut-

ton for one second again.

WiththelampstatusON,pulltheswitchtriggertoturnon

thelamp.Toturnoff,releaseit.Thelampgoesoutapprox-

imately 10 seconds after releasing the switch trigger.

WiththelampstatusOFF,thelampdoesnotturnon

even if pulling the trigger.

NOTE:Toconrmthelampstatus,pullthetrigger.

Whenthelamplightsupbypullingtheswitchtrigger,

thelampstatusisON.Whenthelampdoesnotcome

on, the lamp status is OFF.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

NOTE:Whilepullingtheswitchtrigger,thelamp

status cannot be changed.

NOTE:Forapproximately10secondsafterreleasing

the switch trigger, the lamp status can be changed.

Reversing switch action

►Fig.8: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION:

Use the reversing switch only after

the tool comes to a complete stop. Changing the direc-

tion of rotation before the tool stops may damage the tool.

CAUTION:

When not operating the tool, always

set the reversing switch lever to the neutral position.

Thistoolhasareversingswitchtochangethedirection

of rotation. Depress the reversing switch lever from the

AsideforclockwiserotationorfromtheBsideforcoun-

terclockwise rotation.

Whenthereversingswitchleverisintheneutralposi-

tion, the switch trigger cannot be pulled.

Changing the impact force/mode

►Fig.9: 1. Changed in four steps 2. Hard impact

mode 3. Medium impact mode 4. Soft impact

mode 5. Reverse rotation auto stop mode

6. Button

Youcanchangetheimpactmodeinfoursteps:hard,

medium, soft, and reverse rotation auto stop mode.

Toselectthestep,pressthebutton

Forapproximatelyoneminuteafterreleasingtheswitch

trigger, the impact force can be changed.

Hard, Medium, and Soft impact mode allows a tighten-

ing suitable to the work.

Thefunctionofreverserotationautostopmodeworks

only with pulling the trigger fully in counterclockwise tool

rotation.Whenthebolt/nutgetsenoughloosened,the

tool stops the impact and rotation.

Specications of each impact force grade

Impact force grade displayed

on panel

Maximum blows Application Work

Hard

3,500 min

-1

(/min) Tighteningwhenforceand

speed are desired.

Assemblingthesteelframe.

Medium

2,600 min

-1

(/min) Tighteningwhenyouneed

good controlled power.

Assemblingordisassembling

scaffolds or framework.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTW285 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info