Bedienungsanleitung Makita DUC204 (Seite 14 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690904

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

14 ENGLISH

YoucanusethetoolintheTorqueBoostmodefor

cuttingthickbranchesorhardbranches.Tousethetool

intheTorqueBoostmode,whenthetoolisturnedoff,

press the main power switch for a few seconds until the

main power lamp lights up in yellow.

NOTE:YoucanusethetoolintheTorqueBoost

mode up to 30 seconds. Depending on the usage

conditions, this mode shifts to the normal mode in

less than 30 seconds.

NOTE: If the main power lamp blinks in yellow when

you press the main power switch for a few seconds,

theTorqueBoostmodeisnotavailable.Inthiscase,

follow the steps below.

• TheTorqueBoostmodeisnotavailableright

after the cutting operation. Wait for more than 10

seconds, and then press the main power switch

again.

• IfyouusetheTorqueBoostmodeseveraltimes,

theuseoftheTorqueBoostmodeisrestrictedto

protectthebattery.IftheTorqueBoostmodeis

not available after waiting for more than 10 sec-

onds, replace the battery cartridge with a fully

charged one, or recharge the battery cartridge.

NOTE: If the main power lamp lights up in red or

blinks in red or green, refer to the instructions for tool/

battery protection system.

NOTE:TheTorqueBoostmodecannotbeusedwhen

the battery cartridge BL1815N, BL1820, or BL1820B

is installed.

Switch action

WARNING: For your safety, this tool is

equipped with lock-off lever which prevents the

tool from unintended starting. NEVER use the tool

if it runs when you simply pull the switch trigger

without pressing the lock-off lever. Return the

tool to our authorized service center for proper

repairs BEFORE further usage.

WARNING: NEVER tape down or defeat pur-

pose and function of lock-off lever.

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

NOTICE: Do not pull the switch trigger hard with-

out pressing the lock-off lever. This can cause

switch breakage.

Topreventtheswitchtriggerfrombeingaccidentally

pulled,alock-offleverisprovided.Tostartthetool,

depress the lock-off lever and pull the switch trigger.

Thetoolspeedincreasesbyincreasingpressureonthe

switch trigger. Release the switch trigger to stop.

►Fig.6: 1. Switch trigger 2. Lock-off lever

Checking the chain brake

CAUTION: Hold the chain saw with both

hands when switching it on. Hold the top handle

with your right hand, the front handle with your

left. The bar and the chain must not be in contact

with any object.

CAUTION: Should the saw chain not stop

immediately when this test is performed, the

saw may not be used under any circumstances.

Consult our authorized service center.

1. Press the lock-off lever, then pull the switch trig-

ger.Thesawchainstartsimmediately.

2. Push the front hand guard forwards with the back

of your hand. Make sure that the chain saw comes to an

immediate standstill.

►Fig.7: 1. Front hand guard 2. Unlocked position

3. Locked position

Checking the run-down brake

CAUTION: If the saw chain does not stop

within two seconds in this test, stop using the

chain saw and consult our authorized service

center.

Run the chain saw then release the switch trigger com-

pletely.Thesawchainmustcometoastandstillwithin

two seconds.

Adjusting the chain lubrication

Youcanadjusttheoilpumpfeedratewiththeadjusting

screwusingtheuniversalwrench.Theamountofoil

canbeadjustedin3steps.

►Fig.8: 1.Adjustingscrew

Carabiner (rope attachment point)

You can hang the tool by attaching the rope to the cara-

biner. Pull up the carabiner, and then tie it with the rope.

Electronic function

Thetoolisequippedwiththeelectronicfunctionsfor

easy operation.

• Softstart

Thesoft-startfunctionminimizesstart-upshock,

and makes the tool start smoothly.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

CAUTION: Do not touch the saw chain with

bare hands. Always wear gloves when handling

the saw chain.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUC204 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info