Bedienungsanleitung Makita DUC204 (Seite 15 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690904

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

15 ENGLISH

Removing or installing saw chain

CAUTION: The saw chain and the guide bar

are still hot just after the operation. Let them cool

down enough before carrying out any work on

the tool.

CAUTION: Carry out the procedure of install-

ing or removing saw chain in a clean place free

from sawdust and the like.

Toremovethesawchain,performthefollowingsteps:

1. Release the chain brake by pulling the front hand

guard.

2. Loosenthechainadjustingscrew,thentheretain-

ing nut.

►Fig.9: 1.Chainadjustingscrew2. Retaining nut

3. Remove the sprocket cover then remove the saw

chain and guide bar from the chain saw body.

Toinstallthesawchain,performthefollowingsteps:

1. Check the direction of the saw chain. Match the

direction of the saw chain with that of the mark on the

chain saw body.

2. Fit one end of the saw chain on the top of the

guide bar.

3. Fit the other end of the saw chain around the

sprocket, then attach the guide bar to the chain saw

body, aligning the hole on the guide bar with the pin on

the chain saw body.

►Fig.10: 1. Sprocket 2. Hole

4. Insert the protrusion on the sprocket cover to the

chain saw body, and then close the cover so that the

bolt and pins on the chain saw body meet their counter-

parts on the cover.

►Fig.11: 1. Protrusion 2. Sprocket cover 3. Bolt 4. Pin

5. Tightentheretainingnuttosecurethesprocket

cover,thenloosenitabitfortensionadjustment.

►Fig.12: 1. Retaining nut

Adjusting saw chain tension

CAUTION: Do not tighten the saw chain too

much. Excessively high tension of saw chain may

cause breakage of saw chain, wear of the guide bar

andbreakageoftheadjustingdial.

CAUTION: A chain which is too loose can

jump off the bar and it may cause an injury

accident.

Thesawchainmaybecomelooseaftermanyhours

of use. From time to time check the saw chain tension

before use.

1. Release the chain brake by pulling the front hand

guard.

2. Loosen the retaining nut a bit to loosen the

sprocket cover lightly.

►Fig.13: 1. Retaining nut

3. Liftuptheguidebartipslightlyandadjustthe

chaintension.Turnthechainadjustingscrewclockwise

to tighten, turn it counterclockwise to loosen.

For chain blade 90PX and 91PX:

Tightenthesawchainuntilthelowersideofthesaw

chaintsintheguidebarrailasillustrated.

►Fig.14: 1. Guide bar 2. Saw chain 3.Chainadjust-

ing screw

For chain blade 25AP:

Tightenthesawchainsothatthegapbetweenthecen-

ter of the lower side of the guide bar and the saw chain

becomes approximately 1 mm to 2 mm.

4. Keep holding the guide bar lightly and tighten the

sprocket cover.

For chain blade 90PX and 91PX:

Make sure that the saw chain does not loose at the

lower side.

For chain blade 25AP:

Make sure that the gap between the center of the lower

side of the guide bar and the saw chain is approximately

1 mm to 2 mm.

5. Tightentheretainingnuttosecurethesprocket

cover.

►Fig.15: 1. Retaining nut

Makesurethesawchaintssnuglyagainstthelower

side of the bar.

Spike bumper

Optional accessory

When cutting thick branches, using the spike bumper is

recommended.Toinstallthespikebumper,performthe

following steps:

1. Remove the sprocket cover, saw chain, and guide

bar.

2. Align the holes of the spike bumper with the holes

on the chain saw body, and then tighten the screws

rmly.

►Fig.16: 1. Screw 2. Spike bumper

OPERATION

Lubrication

Saw chain is automatically lubricated when the tool is in

operation. Check the amount of remaining oil in the oil

tank periodically through the oil inspection window.

Torellthetank,laythechainsawonitssideand

removetheoiltankcap.Theproperamountofoilis140

ml.Afterrellingthetank,makesurethattheoiltank

cap is tightened securely.

►Fig.17: 1. Oil tank cap 2. Oil inspection window

Afterrelling,holdthechainsawawayfromthe

tree. Start it and wait until lubrication on saw chain is

adequate.

►Fig.18

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUC204 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info