Bedienungsanleitung Makita DUC405Z (Seite 13 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711173

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

13 ENGLISH

Indicator lamps Remaining

capacity

Lighted Off Blinking

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Main power switch

WARNING: Always turn off the main power

switch when not in use.

To stand by the chain saw, press the main power switch

until the main power lamp lights up. To turn off, press

the main power switch again.

►Fig.6: 1. Main power switch

NOTE:

The main power lamp brinks if the switch trigger is

pulled under unoperatable conditions. The lamp blinks if you

• turn on the main power switch while holding

down the lock-off lever and the switch trigger;

•

pull the switch trigger while the chain brake is applied;

• release the chain brake while holding down the

lock-off lever and pulling the switch trigger.

NOTE: This chain saw employs the auto power-off

function. To avoid unintentional start up, the main

power switch will automatically shut down when the

switch trigger is not pulled for a certain period after

the main power switch is turned on.

Switch action

WARNING: For your safety, this tool is

equipped with lock-off lever which prevents the

tool from unintended starting. NEVER use the tool

if it runs when you simply pull the switch trigger

without pressing the lock-off lever. Return the

tool to our authorized service center for proper

repairs BEFORE further usage.

WARNING: NEVER tape down or defeat pur-

pose and function of lock-off lever.

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

NOTICE: Do not pull the switch trigger hard with-

out pressing the lock-off lever. This can cause

switch breakage.

To prevent the switch trigger from being accidentally

pulled, a lock-off lever is provided. To start the tool,

depress the lock-off lever and pull the switch trigger.

Tool speed is increased by increasing pressure on the

switch trigger. Release the switch trigger to stop.

►Fig.7: 1. Switch trigger 2. Lock-off lever

Checking the chain brake

CAUTION: Hold the chain saw with both

hands when switching it on. Hold the rear handle

with your right hand, the front handle with your

left. The bar and the chain must not be in contact

with any object.

CAUTION: Should the saw chain not stop

immediately when this test is performed, the

saw may not be used under any circumstances.

Consult our authorized service center.

1. Press the lock-off lever, then pull the switch trig-

ger. The saw chain starts immediately.

2. Push the front hand guard forwards with the back

of your hand. Make sure that the chain saw comes to an

immediate standstill.

►Fig.8: 1. Front hand guard 2. Unlocked position

3. Locked position

Checking the run-down brake

CAUTION:

If the saw chain does not stop

within one second in this test, stop using the chain

saw and consult our authorized service center.

Run the chain saw then release the switch trigger com-

pletely. The saw chain must come to a standstill within

one second.

Adjusting the chain lubrication

Youcanadjusttheoilpumpfeedratewiththeadjusting

screw.Theamountofoilcanbeadjustedusingthe

universal wrench.

►Fig.9: 1.Adjustingscrew

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

CAUTION: Do not touch the saw chain with

bare hands. Always wear gloves when handling

the saw chain.

Removing or installing saw chain

CAUTION: The saw chain and the guide bar

are still hot just after the operation. Let them cool

down enough before carrying out any work on

the tool.

To remove the saw chain, perform the following steps:

1. Release the chain brake by pulling the front hand

guard.

2. Loosenthechainadjustingscrew,thentheretain-

ing nuts.

►Fig.10: 1.Chainadjustingscrew2. Retaining nut

3. Sprocket cover

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUC405Z Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info