Bedienungsanleitung Makita DUC405Z (Seite 14 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711173

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

14 ENGLISH

3. Remove the sprocket cover then remove the saw

chain and guide bar from the chain saw body.

To install the saw chain, perform the following steps:

1. Make sure the direction of the chain. The arrow

mark on the chain shows the direction of the chain.

2. Fit in one end of the saw chain on the top of the

guide bar and the other end around the sprocket.

►Fig.11: 1. Sprocket

3. Rest the guide bar in place on the chain saw.

4. Place the sprocket cover on the chain saw so that

theadjustingpinispositionedinasmallholeonthe

guide bar.

►Fig.12: 1. Sprocket cover 2. Guide bar 3. Hole

4.Adjustingpin

5. Tighten the retaining nuts to secure the sprocket

cover,thenloosenitabitfortensionadjustment.

►Fig.13: 1. Retaining nut

Adjusting saw chain tension

CAUTION: Carry out the procedure of install-

ing or removing saw chain in a clean place free

from sawdust and the like.

CAUTION: Do not tighten the saw chain too

much. Excessively high tension of saw chain may

cause breakage of saw chain, wear of the guide bar

andbreakageoftheadjustingdial.

CAUTION: A chain which is too loose can

jump off the bar and it may cause an injury

accident.

The saw chain may become loose after many hours

of use. From time to time check the saw chain tension

before use.

1. Release the chain brake by pulling the front hand

guard.

2. Loosen the retaining nuts a bit to loosen the

sprocket cover lightly.

►Fig.14: 1. Retaining nut

3. Liftuptheguidebartipslightlyandadjustthe

chaintension.Turnthechainadjustingscrewclockwise

to tighten, turn it counterclockwise to loosen.

Tighten the saw chain until the lower side of the saw

chaintsintheguidebarrailasillustrated.

►Fig.15: 1. Guide bar 2. Saw chain 3.Chainadjust-

ing screw

4. Keep holding the guide bar lightly and tighten the

retaining nuts to secure the sprocket cover.

►Fig.16: 1. Retaining nut

Make sure that the saw chain does not loose at the

lowersideandthesawchaintssnuglyagainstthe

lower side of the bar.

OPERATION

Lubrication

Saw chain is automatically lubricated when the tool is in

operation. Check the amount of remaining oil in the oil

tank periodically.

Torellthetank,laythechainsawonitssideand

remove the oil tank cap. The proper amount of oil is 200

ml.Afterrellingthetank,makesurethattheoiltank

cap is tightened securely.

►Fig.17: 1. Oil tank cap 2. Oil tank (translucent)

Afterrelling,holdthechainsawawayfromthe

tree. Start it and wait until lubrication on saw chain is

adequate.

►Fig.18

NOTICE: When lling the chain oil for the rst

time, or relling the tank after it has been com-

pletely emptied, add oil up to the bottom edge of

the ller neck. The oil delivery may otherwise be

impaired.

NOTICE: Use the saw chain oil exclusively for

Makita chain saws or equivalent oil available in

the market.

NOTICE: Never use oil including dust and parti-

cles or volatile oil.

NOTICE: When pruning trees, use botanical oil.

Mineral oil may harm trees.

NOTICE: Before the cutting operation, make sure

that the provided oil tank cap is screwed in place.

WORKING WITH THE CHAIN SAW

CAUTION: The rst time user should, as a

minimum practice, do cutting logs on a saw-horse

or cradle.

CAUTION: When sawing precut timber, use a

safe support (saw horse or cradle). Do not steady

the workpiece with your foot, and do not allow

anyone else to hold or steady it.

CAUTION: Secure round pieces against

rotation.

CAUTION: Keep all parts of the body away

from the saw chain when the motor is operating.

CAUTION: Hold the chain saw rmly with

both hands when the motor is running.

CAUTION: Do not overreach. Keep proper

footing and balance at all times.

NOTICE: Never toss or drop the tool.

NOTICE: Do not cover the vents of the tool.

Bring the bottom edge of the chain saw body into

contact with the branch to be cut before switching on.

Otherwise it may cause the guide bar to wobble, result-

ingininjurytooperator.Sawthewoodtobecutbyjust

moving it down by using the weight of the chain saw.

►Fig.19

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUC405Z Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info