Bedienungsanleitung Makita DUR182L (Seite 12 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599970

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Parts description (Fig. 4)

FUNCTIONAL DESCRIPTION

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before adjusting or

checking the functions on the tool. Failure to switch

off and remove the battery cartridge may result in

serious personal injury from accidental start-up.

Installing or removing battery cartridge

(Fig. 5)

CAUTION:

• Always switch off the tool before installing or removing

of the battery cartridge.

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury.

To remove the battery cartridge, slide it from the tool while

sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip it

into place. Insert it all the way until it locks in place with a

little click. If you can see the red indicator on the upper

side of the button, it is not locked completely.

CAUTION:

• Always install the battery cartridge fully until the red

indicator cannot be seen. If not, it may accidentally fall

out of the tool, causing injury to you or someone

around you.

• Do not install the battery cartridge forcibly. If the

cartridge does not slide in easily, it is not being inserted

correctly.

Power switch action

WARNING:

• Before inserting the battery cartridge in the tool,

always check to see that the switch trigger

actuates properly and returns to the “OFF”

position when released. Do not pull the switch

trigger hard without turning the lock-off lever. This

can cause switch breakage. Operating a tool with a

switch that does not actuate properly can lead to loss

of control and serious personal injury. (Fig. 6)

Push the power button on the housing so that the tool is

powered on and power indicator lights. (Fig. 7)

To prevent the switch trigger from being accidentally

pulled, a lock-off lever is provided.

To start the tool, turn the lock-off lever and then pull the

switch trigger. Release the switch trigger to stop.

NOTE:

• After the power button is pushed and the tool is left one

minute without any operations, the tool is automatically

powered off.

Reversing switch for debris removal

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before removing

weeds or debris entangled in the tool that could not

be removed when operated in the reverse mode.

Failure to switch off and remove the battery cartridge

may result in serious personal injury from accidental

start-up. (Fig. 8)

This tool has a reversing switch which is only provided to

change the direction of rotation so that it can be used to

remove weeds and debris entangled in the tool. To

operate the tool normally the “A” side of the switch should

be depressed.

To remove weeds and debris that are jammed in the

rotating head the tool can be reversed by depressing the

“B” side of the switch. In the reverse position the tool will

only operate for a short period of time and automatically

shut off.

NOTICE:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage it.

Speed adjusting dial (Fig. 9)

The tool speed can be infinitely adjusted from 3,500 min

-1

to 6,000 min

-1

with the speed adjusting dial.

Turn the speed adjusting dial clockwise for higher speed,

and counterclockwise for lower speed.

Battery protection system (Lithium-ion

battery with star marking) (Fig. 10)

Lithium-ion batteries with a star marking are equipped

with a protection system. This system automatically cuts

off power to the tool to extend battery life.

The tool will automatically stop during operation if the tool

and/or battery are placed under one of the following

conditions:

• Overloaded:

The tool is operated in a manner that causes it to

draw an abnormally high current.

In this situation, release the switch trigger on the tool

and stop the application that caused the tool to

become overloaded. Then pull the switch trigger

again to restart.

If the tool does not start, the battery is overheated. In

this situation, let the battery cool before pulling the

switch trigger again.

• Low battery voltage:

The remaining battery capacity is too low and the tool

will not operate. In this situation, remove and

recharge the battery.

Indication lamps (Fig. 11)

When the protection system works during the operation,

the lamps light up.

Refer to the following table for the status and action to be

taken for the indication lamp.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUR182L Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita DUR182L

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info