Bedienungsanleitung Makita DUR182L (Seite 14 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599970

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

spindle directly and tighten it by turning it

counterclockwise. Remove the hex wrench.

To remove the nylon cutting head, turn the nylon cutting

head clockwise while holding the receive washer with the

hex wrench.

CAUTION:

• If during operation the nylon cutting head

accidentally impacts a rock or hard object the

trimmer should be stopped and inspected for any

damage. If the nylon cutting head is damaged it

should be replaced immediately. Use of a damaged

nylon cutting head could result in serious personal

injury.

OPERATION

Correct handling of tool

Attachment of shoulder harness (Fig. 24)

Put the shoulder harness on. Then connect the buckles

on both the hook and the harness. Be sure that the

buckles click and lock completely in place.

Only for model DUR183L (Fig. 25)

When the cap is not in use, hang it on the hook.

Detachment (Fig. 26)

The buckle is provided with a means of quick release.

Simply squeeze the sides and the buckle to release the

tool.

WARNING:

• Be extremely careful to maintain control of the tool

at all times. Do not allow the tool to be deflected

toward you or anyone in the work vicinity. Failure to

keep control of the tool could result in serious injury to

the bystander and the operator.

Adjustment of the hanger position and shoulder

harness (Fig. 27)

To change the hanger position, loosen the hex bolt on the

hanger with the supplied wrench. Then move the hanger.

After adjusting the hanger position, tighten the hex bolt

with the wrench securely.

MAINTENANCE

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before attempting to

perform inspection or maintenance on the tool.

Failure to switch off and remove the battery cartridge

may result in serious personal injury from accidental

start-up.

NOTICE:

Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing the nylon cord

WARNING:

• Make sure that the cover of the nylon cutting head

is secured to the housing properly as described

below. Failure to properly secure the cover may cause

the nylon cutting head to fly apart resulting in serious

personal injury. (Fig. 28)

Take off cover from housing, pressing two latches which

are slotted section oppositely on side of housing. (Fig. 29)

Cut a nylon line in 3-6 m. Fold the cutting line in two

halves, leave one of half longer 80-100 mm than another.

(Fig. 30)

Hook the middle of the new nylon cord to the notch

located at the center of the spool between the 2 channels

provided for the nylon cord.

Wind both ends firmly around the spool in the direction

marked on the head for left hand direction indicated by

LH. (Fig. 31)

Wind all but about 100 mm of the cords, leaving the ends

temporarily hooked through a notch on the side of the

spool. (Fig. 32)

Mount the spool on the cover so that the grooves and

protrusions on the spool match up with those on the

cover. Now, unhook the ends of the cord from their

temporary position and feed the cords through the eyelets

to come out of the cover. (Fig. 33)

Align the protrusion on the underside of the cover with the

slots of the eyelets. Then push the cover firmly onto the

housing to secure it. Make sure the latches fully spread in

the cover.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

TROUBLE SHOOTING

Before asking for repairs, conduct your own inspection

first. If you find a problem that is not explained in the

manual, do not attempt to dismantle the tool. Instead, ask

Makita Authorized Service Centers, always using Makita

replacement parts for repairs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUR182L Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita DUR182L

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info