Bedienungsanleitung Makita DUR188U (Seite 15 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690922

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

15 ENGLISH

►Fig.12: 1. Most effective cutting area

The nylon cutting head is a dual string trimmer head

provided with a bump & feed mechanism.

To feed out the nylon cord, tap the cutting head against

the ground while rotating.

NOTE: If the nylon cord does not feed out while

tapping the head, rewind/replace the nylon cord

by following the procedures described under

“Maintenance”.

ASSEMBLY

WARNING: Always be sure that the tool is

switched off and battery cartridge is removed

before carrying out any work on the tool. Failure to

switch off and remove the battery cartridge may result

inseriouspersonalinjuryfromaccidentalstart-up.

WARNING: Never start the tool unless it is

completely assembled. Operation of the tool in a

partially assembled state may result in serious per-

sonalinjuryfromaccidentalstart-up.

Installing the handle

For DUR187U and DUR188U only

1. Insert the shaft of the handle into the grip. Align

the screw hole in the grip with the one in the shaft.

Tighten the screw securely.

►Fig.13: 1. Grip 2.Screw3. Handle

2. Place handle between handle clamp and handle

holder.Adjustthehandletoananglethatprovidesa

comfortableworkingpositionandthensecurewithhex

socket head bolts.

►Fig.14: 1.Hexsocketheadbolt2. Handle clamp

Mounting the attachment pipe

For DUR188U and DUR188L only

Mount the attachment pipe to the power unit.

1. Turn the lever to the direction of the arrow shown

inthegure.

►Fig.15: 1. Lever

2. Pullupthejointcoverandinserttheattachment

pipe while aligning the protrusion on the pipe (cutting

toolside)withtheconcaveportionofthejointpart.

►Fig.16: 1. Lock lever 2. Joint cover 3. Pipe

Make sure that the surface of the lock lever is parallel

to the pipe.

3. Turn the lever to the direction of the arrow shown

inthegure.

►Fig.17: 1. Lever

To remove the pipe, turn the lever to the direction of the

arrowshowninthegureandpullthepipeoutwhile

pressing down the lock lever.

►Fig.18: 1. Lever 2. Lock lever 3. Pipe

Installing the guard

WARNING: Never use the tool without the

guard illustrated in place. Failure to do so can

causeseriouspersonalinjury.

CAUTION: Take care not to injure yourself on

the cutter for cutting the nylon cord.

NOTE: The shape of the protector varies depending

on the country.

1. Aligntheprojectionsontheprotectorwiththe

grooves of the motor housing.

►Fig.19: 1. Protector 2. Groove 3.Projection

2. Aligntheprojectionsontheprotectorholderwith

its counter parts of the motor housing.

►Fig.20: 1. Protector holder 2.Projection

3. Tightenthehexsocketheadboltssecurelyto

fasten the protector and the protector holder.

►Fig.21: 1.Hexsocketheadbolt2.Hexwrench

Installing the wire guard

CAUTION: Before adjusting the wire guard,

wait for the cutting head comes to standstill. Do

not adjust the wire guard with your foot.

►Fig.22

Toreducetheriskdamagingtheobjectsinfrontofthe

cutting head, insert the wire guard so that it controls the

cutting range of the mowing line.

Slightlyexpandthewireguardoutwardandtheninsert

it into the holes of the protector.

►Fig.23: 1.Wireguard

NOTE:Donotexpandthewireguardoutwardtoo

much. Otherwise it may break.

Whenwireguardisnotinuse,liftitfortheidleposition.

►Fig.24

Installing nylon cutting head

Optional accessory

CAUTION: If the nylon cutting head acciden-

tally impacts a rock or hard object during oper-

ation, stop the tool and inspect for any damage.

If the nylon cutting head is damaged, replace it

immediately. Use of a damaged cutting tool could

resultinseriouspersonalinjury.

CAUTION: Make sure to remove the hex

wrench after installation.

NOTICE: Be sure to use genuine Makita nylon

cutting head.

►Fig.25: 1. Nylon cutting head 2. Metal guard

3.Spindle4.Hexwrench

1. Turn the tool upside down so that you can replace

the cutting tool easily.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUR188U Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info