Bedienungsanleitung Makita DVC265 (Seite 16 von 34) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691489

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

16 ENGLISH

Installing the wireless unit

CAUTION: Place the cleaner on a at and

stable surface when installing the wireless unit.

NOTICE:

Clean the dust and dirt on the cleaner

before installing the wireless unit. Dust or dirt may cause

malfunction if it comes into the slot of the wireless unit.

NOTICE:

To prevent the malfunction caused by

static, touch a static discharging material, such as

a metallic part, before picking up the wireless unit.

NOTICE:

When installing the wireless unit, always

be sure that the wireless unit is inserted in the cor-

rect direction and the lid is completely closed.

1. Openthelidonthecleanerasshowninthegure.

►Fig.32: 1. Lid

Insert the wireless unit to the slot and then close the lid.

Wheninsertingthewirelessunit,aligntheprojections

with the recessed portions on the slot.

►Fig.33: 1. Wireless unit 2.Projection3. Lid

4. Recessed portion

When removing the wireless unit, open the lid slowly.

The hooks on the back of the lid will lift the wireless unit

as you pull up the lid.

►Fig.34: 1. Wireless unit 2. Hook 3. Lid

After removing the wireless unit, keep it in the supplied

case or a static-free container.

NOTICE: Always use the hooks on the back of

the lid when removing the wireless unit. If the

hooks do not catch the wireless unit, close the lid

completely and open it slowly again.

Tool registration for the cleaner

NOTE: A Makita tool supporting the wireless activa-

tion function is required for the tool registration.

NOTE: Finish installing the wireless unit to the tool

before starting the tool registration.

NOTE:

During the tool registration, do not pull the switch

trigger on the tool or push the cleaner's switch for vacuuming.

NOTE: Refer to the instruction manual of the tool, too.

If you wish to activate the cleaner along with the switch

operationofthetool,nishthetoolregistrationbeforehand.

1. Install the wireless units to the cleaner and the

tool, respectively.

2. Install the batteries to the cleaner and the tool.

3. Set the stand-by switch on the cleaner to " I (ON)".

►Fig.35: 1. Stand-by switch

4. Press the wireless activation button on the cleaner

for 3 seconds until the wireless activation lamp blinks in

green. And then press the wireless activation button on

the tool in the same way.

►Fig.36: 1. Wireless activation button 2. Wireless

activation lamp

If the cleaner and the tool are linked successfully, the

wireless activation lamps will light up in green for 2

seconds and start blinking in blue.

NOTE:Thewirelessactivationlampsnishblinking

in green after 20 seconds elapsed. Press the wireless

activation button on the tool while the wireless acti-

vation lamp on the cleaner is blinking. If the wireless

activation lamp does not blink in green, push the wire-

lessactivationbuttonbrieyandholditdownagain.

NOTE: When performing two or more tool registration

forthecleaner,nishthetoolregistrationonebyone.

Starting the wireless activation

function

NOTE: Finish the tool registration for the cleaner for

wireless activation.

NOTE: Always place the cleaner so that you can see

the status of the wireless activation lamp.

NOTE: Refer to the instruction manual of the tool, too.

After registering a tool to the cleaner, the cleaner will

automatically runs along with the switch operation of

the tool.

1. Install the wireless units to the cleaner and the

tool, respectively.

2. Install the batteries to the cleaner and the tool.

3. Connect the hose of the cleaner with the tool.

►Fig.37

4. Set the stand-by switch on the cleaner to " I (ON)".

The wireless activation lamp will blink in blue.

►Fig.38: 1. Stand-by switch

5. Push the wireless activation button on the tool

briey.Thewirelessactivationlampwillblinkinblue.

►Fig.39: 1. Wireless activation button 2. Wireless

activation lamp

6. Pull the switch trigger of the tool. Check if the

cleaner runs while the switch trigger on the tool is being

pulled.

CAUTION: Always check if the wireless acti-

vation function works before starting a work with

the tool.

To stop the wireless activation, push the wireless activa-

tion button on the tool or set the stand-by switch on the

cleaner to "O (OFF)".

NOTE: The wireless activation lamp on the tool will

stop blinking in blue when there is no operation for

2 hours. In this case, press the wireless activation

buttons on the tool again.

NOTE: The cleaner starts/stops with a delay. There is

a time lag when the cleaner detects a switch opera-

tion of the tool.

NOTE: The transmission distance of the wireless unit

may vary depending on the location and surrounding

circumstances.

NOTE: When two or more tools are registered to one

cleaner, the cleaner may start running even if you

don't pull the switch trigger because other user is

using the wireless activation function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DVC265 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info