Bedienungsanleitung Makita DVC861L (Seite 10 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

657968

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Tape or mask off open contacts and pack up the

battery in such a manner that it cannot move around in

the packaging.

11. Follow your local regulations relating to disposal

of battery.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing fires, personal injury and damage. It will also void

the Makita warranty for the Makita tool and charger.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the battery

cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10°C - 40°C (50°F - 104°F). Let a hot

battery cartridge cool down before charging it.

4. Charge the battery cartridge if you do not use it for

a long period (more than six months).

FUNCTIONAL DESCRIPTION

Use with AC power:

WARNING:

• Before plugging the cleaner, always make sure that

the cleaner is switched off. Plugging the cleaner with

the switch on may cause an unexpected start resulting

in serious personal injury.

Connect the plug to a power supply. (Fig. 1)

The AC power indicator lights up when setting the

stand-by switch to “I” side. (Fig. 2)

NOTE:

• Even operating in DC power mode , the tool is

automatically changed into AC power mode when

plugged in.

• If the tool is unplugged during operation with the

battery inserted, the cleaner gets into stand-by state.

Use with battery:

Installing or removing battery cartridge

CAUTION:

• Always be sure that the cleaner is switched off,

unplugged, and the battery cartridge is removed before

adjusting or checking function on the tool.

• Hold the cleaner and the battery cartridge firmly

when installing or removing battery cartridge.

Failure to hold the cleaner and the battery cartridge

firmly may cause them to slip off your hands and result

in damage to the cleaner and battery cartridge and a

personal injury.

• Be careful not to pinch your fingers when opening

or closing the battery cover. Failure to do so may

cause personal injury.

To install the battery cartridge, release the lock first, and

open the battery cover. And then, insert the battery

cartridge. (Fig. 3)

Align the tongue on the battery cartridge with the groove

in the housing and slip it into place. Insert it all the way

until it locks in place with a little click. Then lock the

battery cover. (Fig. 4)

To remove the battery cartridge, slide it from the tool while

sliding the button on the front of the cartridge.

NOTICE:

• Remove the plug of the cleaner from the extension

cord when using the cleaner with the batteries.

CAUTION:

• Always install the battery cartridge fully in place. If not,

it may accidentally fall out of the tool, causing injury to

you or someone around you.

• Do not install the battery cartridge forcibly. If the

cartridge does not slide in easily, it is not being inserted

correctly.

NOTE:

• The cleaner does not work with only one battery

cartridge.

Tool/battery protection system

The tool is equipped with a tool/battery protection system.

This system automatically cuts off power to the motor to

extend tool and battery life.

The tool will automatically stop during operation if the tool

or battery is placed under one of the following conditions.

In some conditions, the indicators light up.

Overload protection

If the tool is overloaded, the tool stops automatically. In

this situation, turn the tool off and stop the application that

caused the tool to become overloaded. Then turn the tool

on to restart.

Overheat protection for tool

015485

When the tool is overheated, the tool stops automatically,

and the battery indicator blink about 60 seconds. In this

situation, let the tool cool down before turning the tool on

again.

Overdischarge protection

When the battery capacity becomes low, the tool stops

automatically. If the product does not operate even when

the switches are operated, remove the batteries from the

tool and charge the batteries.

Remaining battery capacity indication

(Fig. 5 & 6)

Press the check button to make the battery indicators

show the remaining battery capacities. The battery

indicators correspond to each battery.

: On : Blinking

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DVC861L Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info