Bedienungsanleitung Makita EA5001P (Seite 8 von 80) (Englisch, Französisch)

690913

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

10 feet

Wipe off any spilled fuel before starting your saw and

check for leakage.

Check for fuel leakage while refueling and during opera-

tion. If fuel or oil leakage is found, do not start or run the

engine until leak is xed and spilled fuel has been wiped

away. Clothing with fuel on it has to be changed imme-

diately (this is a danger to your life!).

Avoid skin contact with fuel. Never loosen or remove the

cap of the fuel tank while the engine is running.

Starting

Do not drop start. This method is very dangerous because

you may lose control of the saw (g. 6).

WARNING!

Gasoline is an extremely ammable fuel. Use extre-

me caution when handling gasoline or fuel mix. Do

not smoke or bring any sparks or ame near the fuel

(g. 5).

Fueling instructions

Fuel your chain saw in well ventilated areas or out-

doors. Always shut off the engine and allow it to cool before

refueling. Select bare ground for fueling and move the

chain saw at least 10 feet (3 m) from fueling spot before

starting the engine (g. 5a).

Place the chain saw on rm ground or other solid surface

in an open area. Maintain a good balance and secure

footing. Place your right foot through the rear handle

opening and rmly grasp the front handle with your left

hand (g. 6a).

Be absolutely sure that guide bar and chain are clear of

you or all other obstructions and objects, including the

ground, because when the engine starts in semi-throttle

position, engine speed will be fast enough for the clutch

to engage the sprocket and turn the chain which may

cause a kickback.

Never attempt to start the saw when the guide bar is in

a cut or kerf.

When you pull the starter grip, don’t wrap the starter rope

around your hands. Do not allow the grip to snap back,

but guide the starter rope slowly back to permit the rope

to rewind properly.

Failure to follow this procedure may result in injury to hand

or ngers and may damage the starter mechanism.

Chain saw operating instructions

For assembly follow the procedure in the appropriate section

"Mounting Guide Bar and Chain" of this manual. MAKITA

chain, guide bar and sprocket must match each other (see

the appropriate section in this manual).

WARNING!

Proper tension of the chain is extremely important. In

order to avoid false setting the tensioning procedure

must be followed as described in this manual. Always

make sure the hexagonal nut(s) for the sprocket

guard is (are) tightened securely after tensioning the

chain.

Check chain tension once more after having tightened

the nuts and thereafter at regular intervals (always be-

fore starting to work). If the chain becomes loose while

cutting, shut off the engine and then tighten. Never try

to tighten the chain while the engine is running!

Fueling

Your MAKITA saw uses on oil-gasoline mixture for fuel

(see chapter "Fuel" of this manual).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EA5001P Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EA5001P

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info