Bedienungsanleitung Makita EB7660TH (Seite 17 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690563

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

- Before

operation

After fuelling Daily (10h) 50h 200h 600h or 2 years

whichever

earlier

Before storage

Oil tube Inspect - - - -

(Note2)

- -

Valve clearance

(intake valve

and exhaust

valve)

Inspect / adjust - - - -

(Note2)

- -

Mufer Inspect / clean - - - -

(Note2)

- -

Combustion

chamber / valve

/ port

Inspect / clean - - - -

(Note2)

- -

Engine Overhaul - - - - -

(Note2)

Carburetor Drain fuel - - - - - -

(Note3)

Note1: Perform initial replacement after 20h operation.

Note2: For inspection, request Authorized Service Agent or a machine shop.

Note3: After emptying the fuel tank, continue to run the engine and drain fuel in the carburetor.

TROUBLE SHOOTING

Before asking for repairs, conduct your own inspection rst. If you nd a problem that is not explained in the manual, do not attempt to dismantle the

tool. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs.

State of abnormality Probable cause (malfunction) Remedy

Engine does not start. Failure to operate primer pump. Push 7 to 10 times.

Low pulling speed of starter rope. Pull strongly.

Lack of fuel. Feed fuel.

Clogged fuel lter. Clean the fuel lter.

Bent fuel tube. Straighten the fuel tube.

Deteriorated fuel. Deteriorated fuel makes starting more difcult. Replace with new

one. (Recommended replacement: 1 month)

Excessive suction of fuel. Set throttle lever from medium speed to high speed, and pull

starter handle until engine starts. If engine will not start still,

remove spark plug, make electrode dry, and reassemble them as

they originally are. Then, start as specied.

Detached plug cap. Attach securely.

Contaminated spark plug. Clean the spark plug.

Abnormal clearance of spark plug. Adjust clearance.

Other abnormality of spark plug. Replace the spark plug.

Abnormal carburetor. Ask our authorized service center to inspect and repair it.

Cannot pull the starter knob. Ask our authorized service center to inspect and repair it.

Engine internal parts problem. Ask our authorized service center to inspect and repair it.

Engine stops soon.

Engine speed does not increase.

Insufcient warm-up. Perform warm-up operation.

Choke lever is set to “CLOSE” although engine is

warmed up.

Set to “OPEN”.

Clogged fuel lter. Clean the fuel lter.

Contaminated or clogged air cleaner. Clean the air lter.

Detached control cable. Attach the control cable securely.

Engine internal parts problem. Ask our authorized service center to inspect and repair it.

Throttle does not return to idling speed. Inproper throttle valve position. Reposition the control cable.

Adjust the throttle valve position by turning the cable adjusting

bolt.

Engine does not stop.

Run engine at idling, and set choke lever

to “CLOSE”.

Detached connector. Attach the connector securely.

Abnormal electric system. Ask our authorized service center to inspect and repair it.

17 ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EB7660TH Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info