Bedienungsanleitung Makita EM2654LHC (Seite 18 von 84) (Englisch, Portugiesisch, Spanisch)

690576

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

MAINTENANCE

Adjustment of low-speed rotation (idling)

Whenitisnecessarytoadjustthelow-speedrotation(idling),performitbythe

carburetoradjustingscrew.

Checkup of low-speed rotation

CAUTION:

Thecuttingattachmentmaybespinningduringcarburetoradjustments.Wear

your protective equipment and observe all safety instructions. Be sure the

cutting attachment stops turning when the engine idles.

CAUTION:

When the unit is turned off, make sure the cutting attachment has stopped

before the unit is set down.

– Set the low-speed rotation to 3,000 min

-1

 Ifitisnecessarytochangetherotationspeed,regulatetheadjustingscrew

(1) with Phillips screwdriver.

– Turntheadjustingscrewtotheright,andtheenginerotationwillincrease.

Turntheadjustingscrewtotheleft,andtheenginerotationwilldrop.

– Thecarburetor(2)isgenerallyadjustedbeforeshipment.Ifitisnecessaryto

readjustit,pleasecontactAuthorizedServiceAgent.

(1)

(2)

Throttle lever

To prevent the throttle lever (1) from being accidentally pulled, a lock-off lever

(2) is provided. To increase the engine speed, grasp the rear handle (the lock-

off lever is released by the grasp) and then pull the throttle lever.

To decrease the engine speed, release the throttle lever.

CAUTION: Before doing any work on the Petrol Brushcutter, always stop the engine and pull the plug cap off the spark plug (see “checking the

spark plug”).

Always wear protective gloves!

To ensure a long service life and to avoid any damage to the equipment, the following servicing operations should be performed at regular

intervals.

Daily checkup and maintenance

– Before operation, check the machine for loose screws or missing parts. Pay particular attention to the tightness of the cutter blade or nylon

cutting head.

– Beforeoperation,alwayscheckforcloggingofthecoolingairpassageandthecylinderns.

Clean them if necessary.

– Perform the following work daily after use:

• CleanthePetrolBrushcutterexternallyandinspectfordamage.

• Cleantheairlter.Whenworkingunderextremelydustyconditions,cleantheltertheseveraltimesaday.

• Checkthebladeorthenyloncuttingheadfordamageandmakesureitisrmlymounted.

• Checkthatthereissufcientdifferencebetweenidlingandengagementspeedtoensurethatthecuttingtoolisatastandstillwhilethe

engine is idling (if necessary reduce idling speed).

Ifunderidlingconditionsthetoolshouldstillcontinuetorun,consultyournearestAuthorizedServiceAgent.

– Check the functioning of the I-O switch, the lock-off lever, the control lever, and the look button.

Metal blade resharpening

CAUTION:

Themetalbladesmustonlyberesharpenedbyanauthorizedfacility.Manualresharpeningmayresultinimbalancesofthecuttingtoolcausing

vibrations and damage to the equipment.

NOTE: To increase the service life of the cutter blade it may be turned over once, until both cutting edges have become blunt.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EM2654LHC Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info