Bedienungsanleitung Makita EM2654LHC (Seite 20 von 84) (Englisch, Portugiesisch, Spanisch)

690576

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

CLEANING OF AIR CLEANER

DANGER: INFLAMMABLES STRICTLY PROHIBITED

Interval of Cleaning and Inspection: Daily (every 10 operating hours)

– Turn the choke lever to the full close side, and keep the carburetor off from

dust or dirt.

– Loosenthexingbolt.

– Remove the air cleaner cover by pulling its bottom side.

– Remove the elements and tap them to remove dirt.

– If the elements are heavily contaminated:

Remove the elements, immerse them in warm water or in water-diluted

neutraldetergent,anddrythemcompletely.Donotsqueezeorrubthem

when washing.

– Beforeattachingtheelements,besuretodrythemcompletely.Insufcient

dryingoftheelementsmayleadtodifcultstartup.

– Wipe out oil adhering around the air cleaner cover and the breather part with

waste cloth.

– Fit the element (sponge) into the element (felt).

Fit the elements into the plate so that the sponge faces the air cleaner cover.

– Immediatelyattachthecleanercoverandtightenitwithxingbolts.(In

remounting,rstplacetheupperclaw,andthenthelowerclaw.)

Plate

Element (sponge)

Air cleaner

cover

Fixing bolt

Element (felt)

Breather Part

POINTS ON OIL

– Never discard replaced engine oil in garbage, earth or sewage ditch. Disposal of oil is regulated by law. In disposal, always follow the

relevantlawsandregulations.Foranypointsremainingunknown,contactAuthorizedServiceAgent.

– Oil will deteriorate even when it is kept unused. Perform inspection and replacement at regular intervals (replace with new oil every 6

months).

NOTICE:

– Clean the elements several times a day, if excessive dust adheres to it.

Dirtyelementsreduceenginepowerandmakestartingenginedifcult.

– Remove oil on the elements. If operation continues with the elements

remaining not cleared of oil, oil in the air cleaner may fall outside,

resulting in contamination of the environment.

– Do not put the elements on the ground or dirty place. Otherwise they

pick up dirt or debris and it may damage the engine.

– Never use fuel for cleaning the elements. Fuel may damage them.

Choke

lever

0.7 mm - 0.8 mm

(0.028” - 0.032”)

CHECKING THE SPARK PLUG

– Only use the supplied universal wrench to remove or to install the spark plug.

– The gap between the two electrodes of the spark plug should be 0.7 - 0.8 mm

(0.028”-0.032”).Ifthegapistoowideortoonarrow,adjustit.Ifthespark

plug is clogged or contaminated, clean it thoroughly or replace it.

CAUTION: Never touch the spark plug connector while the engine is running

(danger of high voltage electric shock).

Gear case

Grease hole

SUPPLY OF GREASE TO GEAR CASE

– Supply grease (Shell Alvania 2 or equivalent) to the gear case through the

grease hole every 30 hours. (Genuine MAKITA grease may be purchased

from your MAKITA dealer.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EM2654LHC Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info