Bedienungsanleitung Makita EW3050H (Seite 13 von 32) (Alle Sprachen)

690621

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

9. CLEANING PUMP INSIDE

(See Fig. - – )

(Except EW2050H, EW3050H)

If the inside of the pump is plugged up with small rocks

or if the inside of the pump has to be cleaned, you can

clean the inside of the pump by removing the casing

cover using the Hexagon wrench that comes with the

pump.

The accessory Hexagon wrench (8 mm) is attached to

the upper part of the casing. (See Fig.

- )

(1) Removal of the casing cover (See Fig.

- )

Remove the 4 socket bolts.

(2) Cleaning the inside of the pump (See Fig.

- )

After removing the pebbles and dirt from the inside

of the pump, rinse it out with clean water.

Explanation of Fig. -

Casing cover O-Ring

Make sure not to damage the O-ring as this will cause

water leakage.

If the O-ring is deteriorated or damaged, replace it with

a new one.

(3) Reattaching the casing cover (See Fig.

- )

Tighten the 4 socket bolts.

6. PREPARATIONS FOR STORAGE

1. WATER (See Fig. - )

Drain all water from the drain plug.

CAUTION

When retightening drain plug, be sure to

clean the drain plug and the thread of casing.

Otherwise, the thread may be damaged.

2. DISCONNECT THE DELIVERY HOSE

Tilt the pump and drain all water from delivery hole.

Severe damage to pump may result if water freezes in

the pumping chamber.

3. DISCHARGE FUEL

(See Fig. - )

WARNING

Flame Prohibited

If you do not use the engine more than 1 month,

discharge fuel to prevent gum in the fuel system and

carburetor parts.

WARNING

■

Remove the statistic electricity from your

body before relling the gasoline.

Sparking from electrostatic discharge may

cause the ignition to the vaporized fuel

(gasoline) resulting burns.

Static electricity can be discharged from

the body by touching by hand the metal

parts of the unit.

■

Always store/carry the fuel (gasoline) with

metallic portable tank to prevent re.

■

Remove the strainer cup, place the strainer over a

container and open the strainer valve to discharge

fuel from the fuel tank.

■

Remove the drain screw of the carburetor oat

chamber and discharge fuel.

4. ENGINE OIL (See Fig. - )

■

Change the engine oil with fresh oil.

■

Remove the spark plug, pour about 5 cc of engine

oil into the cylinder, slowly pull the starter handle

of the recoil starter 2 or 3 times, and reinstall the

spark plug.

5. CLEAN AND STORE

■

Slowly pull the recoil starter handle until resistance

is felt and leave it in that position.

■

Clean the pump thoroughly with an oiled cloth, put

the cover on, and store the pump indoors in a well

ventilated, low humidity area.

7. OIL SENSOR INSTRUCTIONS

1. FUNCTION OF OIL SENSOR

The engine will stop automatically when the oil level

falls below the safety limit. The engine cannot be

started unless the level is raised above the prescribed

limit. (See Fig.

- )

2. RESTARTING

(1) Fill the crankcase with oil up to the proper level.

(2) As for restarting and operating the engine, refer to

section “4. OPERATING YOUR PUMP” on page 6.

■

Check the wire connector from the engine. It must

be connected securely to the wire from oil sensor.

■

When selecting the engine oil, refer to page 5 for the

recommended oil.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EW3050H Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info