Bedienungsanleitung Makita EW3050H (Seite 12 von 32) (Alle Sprachen)

690621

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

4. ENGINE OIL CHANGE (See Fig. - , )

Initial oil change : After 20 hours of operation

Thereafter : Every 100 hours of operation

(1) When changing oil, stop the engine and loosen the

drain plug. Drain the used oil while the engine is

warm. Warm oil drains quickly and completely.

CAUTION

To prevent injury, pay attention to the hot oil.

Make sure the fuel cap is tightly secured to

avoid spillage.

(2) Re-install the drain plug before relling oil.

Model Oil capacity

EW2050H

EW3050H

EW2051H

EW3051H

0.6 L

(3) Refer to page 5 for the recommended oil.

■

Always use the best grade and clean oil.

Contaminated oil, poor quality oil and shortage of

oil cause damage to engine or shorten the engine

life.

5. CLEANING FUEL CUP (See Fig. - )

WARNING

Flame Prohibited

WARNING

Remove the statistic electricity from your

body before relling the gasoline.

Sparking from electrostatic discharge may

cause the ignition to the vaporized fuel

(gasoline) resulting burns.

Static electricity can be discharged from the

body by touching by hand the metal parts

of the unit.

(1) Inspect fuel cup for water and dirt.

(See Fig.

- - )

(2) To remove water and dirt, close the fuel valve and

remove the fuel cup.

(3) After removing dirt and water, wash the fuel cup

with kerosene or gasoline. Reinstall securely to

prevent leakage.

6. CLEANING AIR CLEANER

(See Fig. - )

A dirty air cleaner element will cause starting difculty,

power loss, engine malfunctions, and shorten engine

life extremely.

Always keep the air cleaner element clean.

WARNING

Flame Prohibited

■

Urethane Foam cleaning (See Fig.

- - )

Wash and clean the urethane foam with detergent.

After cleaning, dry it. Clean the urethane foam

element every 50 hours.

■

Second element (See Fig.

- - )

Clean by tapping gently to remove dirt and blow

off dust. Never use oil. Clean the paper element

every 50 hours of operation, and replace element

set every 200 hours.

NOTE

Clean and replace air cleaner elements more often

when operating in dusty environments. Replace the

element in case that dirt or dust can not be removed

and/or that the element is deformed or deteriorated.

7. FUEL HOSE REPLACEMENT

(See Fig. - )

WARNING

■

Take extreme caution when replacing fuel

hose; gasoline is extremely ammable.

■

Remove the statistic electricity from your

body before relling the gasoline.

Sparking from electrostatic discharge may

cause the ignition to the vaporized fuel

(gasoline) resulting burns.

Static electricity can be discharged from

the body by touching by hand the metal

parts of the unit.

Replace the fuel hose every 1,000 hours or every 2

years.

If fuel leaks from fuel hose, replace the fuel hose

immediately.

8. CHECKING BOLTS, NUTS AND SCREWS

■

Retighten loose bolts and nuts.

■

Check for fuel and oil leaks.

■

Replace damaged parts with new ones.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EW3050H Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info