Bedienungsanleitung Makita EY401MP (Seite 8 von 64) (Englisch, Französisch, Portugiesisch, Spanisch)

599912

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Mounting the attachment to a power unit (Fig. 6)

To mount the attachment to a power unit, follow the steps below.

1. Make sure that the lock lever (A) is not tightened.

2. Align the pin (B) with the arrow mark (C).

3. Insert the shaft into the drive shaft of the power unit until the

release button (D) pops up.

4. Tighten the lock lever (A) rmly as shown.

To remove the attachment, loosen the lock lever, press the lock

button and withdraw the shaft.

NOTICE: Do not tighten the lock lever (A) without the shaft of the

attachment inserted. Otherwise the lock lever may tighten the

entrance of the drive shaft too much and damage it.

Assembling saw chain and guide bar

CAUTION: Make sure that the saw chain, guide bar and

sprocket match each other in gauge and pitch.

Assemble the saw chain and guide bar as the following steps.

(Fig. 7- 9)

1. Loosen the nut (A) and remove the bar holder (B).

2. Turn the tension screw (C) counterclockwise until the tensioning

nut (D) touches the left end.

NOTICE: Do not turn the tension screw counterclockwise too much,

otherwise the tension screw and the tensioning nut comes off from

the housing.

3. Fit the saw chain (E) into the groove of guide bar (F). Start the

procedure from the bar nose.

4. Align the position bolt (G) with the notch of the guide bar (H),

and then t the saw chain (E) onto the sprocket (I). Make sure

that the saw chain is kept tting along the guide bar during the

procedure.

5. Install the guide bar (F) so that the tensioning nut (D) ts into the

hole (J) on the guide bar. Holes (K) are not used.

6. Place the saw chain onto the groove of the guide bar properly.

If the saw chain is not placed into the groove of the guide bar

properly at this point, adjust and t it appropriately.

7. Fit the bar holder (B) and tighten the nut (A) securely. Then

loose the nut a half turn as a provision of the chain tension

adjustment.

8. Adjust the chain tension. Refer to the section “Adjusting the

chain tension.”

CAUTION:

Keep the applicable chain tension. Loose tension can cause the •

saw chain derail. (Fig. 10)

To remove the saw chain and guide bar, turn the tension screw (C)

counterclockwise rst.

Pull the saw chain outward to let the saw chain comes out from

the groove of the guide bar, then remove them from the housing.

(Fig. 11)

Adjusting the chain tension

WARNING:

Before check or adjust the chain tension, switch off the motor and •

remove the spark plug cap or the battery cartridge.

Before check or adjust the chain tension, wear protective gloves.•

CAUTION:

Keep the applicable chain tension. Loose tension can cause the •

saw chain to come off during operation. Too tight tension can

damage the saw chain or guide bar.

During operation, check the chain tension frequently. The saw •

chain stretches and becomes loose during operation. When use

a new saw chain, adjust the tension more frequently. (Fig. 12)

Adjust the chain tension as the following steps.

1. Loose the nut (A) a half turn.

2. Hold the bar nose up. Turn the tensioning screw (B) clockwise

until the saw chain ts the underside of the guide bar snugly.

3. Pull the saw chain along the guide bar by hand. If it is hard to

move, turn the tensioning screw counterclockwise slightly and do

the step 2 again.

4. Tighten the nut (A) securely.

Filling the chain oil tank

The saw chain must be lubricated with chain oil during operation.

Before operation, ll the chain oil tank. After supplying the oil,

tighten the oil cap securely.

Use Makita genuine chain oil only.

NOTICE: Never use waste oil. It may damage the oil pump.

During operation, always pay attention to the oil level. Rell the

tank if the oil level becomes low. The tank becomes empty in

approximately 40 minutes of operation (depending on the setting of

the chain lubrication).

Adjusting the chain-oil feeding rate (Fig. 13 & 14)

The chain-oil feeding rate is adjustable in three steps. According

to the operation, for example cutting hard limbs, adjust the feeding

rate.

To adjust the chain-oil feeding rate, use a at-bladed screwdriver.

Push in the adjusting screw and turn it. To increase feeding rate,

turn the adjusting screw counterclockwise (A). To reduce feeding

rate, turn it clockwise (B).

After adjusting the chain-oil feeding rate, check the feeding rate by

driving the equipment at medium speed.

Inspection and maintenance

WARNING:

Before inspecting or maintaining the equipment, switch off the •

motor and remove the spark plug cap or the battery cartridge.

Otherwise saw chain or other parts may move and result in

serious injury.

Before handling or working around saw chain, wear protective •

gloves. Otherwise the saw chain can cut bare hands severely.

When inspecting or maintaining the equipment, always put it •

down. Assembling or adjusting the equipment in an upright

position may result in serious injury.

Follow the warnings and precautions in the chapter “Safety •

precautions” and the instruction manual of the power unit.

Cleaning the chain-oil feed port (Fig. 15)

Clean the chain-oil feed port (A) daily. To access it, remove the bar

holder and guide bar.

Cleaning and inspecting the guide bar (Fig. 16)

Clean the guide bar daily. Remove saw dust from the groove (A)

and chain-oil feed port (B).

To avoid one side wear of the guide bar, turn it over every time you

replace or sharpen the saw chain.

If the groove is worn, bent or deformed, replace the guide bar.

Inspecting sprocket (Fig. 17)

Check the sprocket for wear every 50 hours of use. Replace it if the

wear marks becomes 0.3 mm or deeper.

Inspecting the saw chain

When you feel the saw chain is worn, deformed, cracked or you

need more effort for the cutting, replace it or ask Makita authorized

service center to sharpen it.

Lubricating moving parts (Fig. 18)

NOTICE: Follow the instruction of the frequency and amount of

grease supplied. Otherwise insufcient lubrication may damage

moving parts.

Gear case:

Remove the grease plug (A) and ll lithium-base grease through the

grease hole (B) every 25 hours of operation.

Drive axle:

Apply grease (Shell Alvania No. 2 or equivalent) every 25 hours of

operation.

Guide bar nose:

Apply grease (Shell Alvania No. 2 or equivalent) from the grease

hole (C) every 10 hours of operation.

Overall inspection

Tighten loose bolts, nuts and screws.•

Check for damaged parts. Ask Makita authorized service center •

to replace them.

Check the bar holder. If there is crack or deformation, replace it. •

Storage

WARNING: Follow the warnings and precautions in the chapter

“Safety precautions” and the instruction manual of the power unit.

When storing the pole saw attachment separated from the power

unit, put the cap onto the end of the shaft. (Fig. 19)

Makita EY401MP Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info