Bedienungsanleitung Makita GA9063R (Seite 8 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691769

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

8 ENGLISH

Safety Warnings Specic for Wire Brushing Operations:

Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress the

wires by applying excessive load to the brush. The

wire bristles can easily penetrate light clothing and/or skin.

If the use of a guard is recommended for wire brush-

ing, do not allow any interference of the wire wheel or

brush with the guard. Wire wheel or brush may expand

in diameter due to work load and centrifugal forces.

Additional Safety Warnings:

When using depressed centre grinding wheels,

be sure to use only berglass-reinforced wheels.

2. NEVER USE Stone Cup type wheels with this

grinder. This grinder is not designed for these

types of wheels and the use of such a product

may result in serious personal injury.

Be careful not to damage the spindle, the ange (espe-

cially the installing surface) or the lock nut. Damage to

these parts could result in wheel breakage.

4. Make sure the wheel is not contacting the

workpiece before the switch is turned on.

Before using the tool on an actual workpiece, let it run

for a while. Watch for vibration or wobbling that could

indicate poor installation or a poorly balanced wheel.

6. Use the specied surface of the wheel to per-

form the grinding.

7. Do not leave the tool running. Operate the tool

only when hand-held.

Do not touch the workpiece immediately after opera-

tion; it may be extremely hot and could burn your skin.

9. Observe the instructions of the manufacturer

for correct mounting and use of wheels.

Handle and store wheels with care.

10. Do not use separate reducing bushings or

adaptors to adapt large hole abrasive wheels.

11. Use only anges specied for this tool.

12. For tools intended to be tted with threaded

hole wheel, ensure that the thread in the wheel

is long enough to accept the spindle length.

13.

Check that the workpiece is properly supported.

14. Pay attention that the wheel continues to

rotate after the tool is switched off.

15.

If working place is extremely hot and humid, or

badly polluted by conductive dust, use a short-cir-

cuit breaker (30 mA) to assure operator safety.

16. Do not use the tool on any materials contain-

ing asbestos.

17. When use cut-off wheel, always work with

the dust collecting wheel guard required by

domestic regulation.

18. Cutting discs must not be subjected to any

lateral pressure.

19. Do not use cloth work gloves during operation.

Fibers from cloth gloves may enter the tool, which

causes tool breakage.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with

product (gained from repeated use) replace strict adher-

ence to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this instruc-

tion manual may cause serious personal injury.

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and unplugged before adjusting or

checking function on the tool.

CAUTION: Return the switch trigger to the

"OFF" position in case of accidental unplugging,

blackout, or the power is cut unintentionally.

Otherwise the tool may start suddenly when the

power returns and it may result in personal injury.

Shaft lock

Press the shaft lock to prevent spindle rotation when

installing or removing accessories.

► Fig.1: 1. Shaft lock

NOTICE: Never actuate the shaft lock when the

spindle is moving. The tool may be damaged.

Switch action

CAUTION: Before plugging in the tool, always

check to see that the switch trigger actuates

properly and returns to the "OFF" position when

released.

► Fig.2: 1. Switch trigger 2. Lock lever

For tool with the lock-on switch

CAUTION: Switch can be locked in "ON" posi-

tion for ease of operator comfort during extended

use. Apply caution when locking tool in "ON"

position and maintain rm grasp on tool.

To start the tool, simply pull the switch trigger (in the B

direction). Release the switch trigger to stop.

For continuous operation, pull the switch trigger (in the B

direction) and then push in the lock lever (in the A direction).

To stop the tool from the locked position, pull the switch

trigger fully (in the B direction), then release it.

For tool with the lock-off switch

To prevent the switch trigger from accidentally pulled, a

lock lever is provided.

To start the tool, push in the lock lever (in the A direc-

tion) and then pull the switch trigger (in the B direction).

Release the switch trigger to stop.

NOTICE: Do not pull the switch trigger hard

without pressing in the lock-off button. This can

cause switch breakage.

For tool with the lock-on and lock-off

switch

CAUTION: Switch can be locked in "ON" posi-

tion for ease of operator comfort during extended

use. Apply caution when locking tool in "ON"

position and maintain rm grasp on tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita GA9063R Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info