Bedienungsanleitung Makita GA9063R (Seite 9 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691769

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

9 ENGLISH

To prevent the switch trigger from accidentally pulled, a

lock lever is provided.

To start the tool, push in the lock lever (in the A direc-

tion) and then pull the switch trigger (in the B direction).

Release the switch trigger to stop.

For continuous operation, push in the lock lever (in the

A direction), pull the switch trigger (in the B direction)

and then pull the lock lever (in the C direction).

To stop the tool from the locked position, pull the switch

trigger fully (in the B direction), then release it.

NOTICE: Do not pull the switch trigger hard

without pressing in the lock-off button. This can

cause switch breakage.

Indication lamp

Only for model GA7063R / GA9063R

► Fig.3: 1. Indication lamp

The indication lamp lights up green when the tool is

plugged.

If the indication lamp does not light up, the mains cord

or the controller may be defective.

The indication lamp is lit but the tool does not start even

if the tool is switched on, the carbon brushes may be

worn out, or the controller, the motor or the ON/OFF

switch may be defective.

Unintentional restart proof

Only for model GA7063R / GA9063R

The tool does not start with the switch being lock-on

even when the tool is plugged.

At this time, the indication lamp ickers red and shows

the unintentional restart proof device is on function.

To cancel the unintentional restart proof, return the

power switch to OFF position.

NOTE: Wait more than one second before restarting

the tool when unintentional restart proof functions.

Soft start feature

Only for model GA7063R / GA9063R

Soft start feature reduces starting reaction.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

Installing side grip (handle)

CAUTION: Always be sure that the side grip is

installed securely before operation.

Screw the side grip securely on the position of the tool

as shown in the gure.

► Fig.4

Installing or removing wheel guard

(For depressed center wheel, ap

disc, ex wheel, wire wheel brush

/ abrasive cut-off wheel, diamond

wheel)

WARNING: When using a depressed center

wheel, ap disc, ex wheel or wire wheel brush,

the wheel guard must be tted on the tool so that

the closed side of the guard always points toward

the operator.

WARNING: When using an abrasive cut-off

/ diamond wheel, be sure to use only the special

wheel guard designed for use with cut-off wheels.

(In some European countries, when using a diamond

wheel, the ordinary guard can be used. Follow the

regulations in your country.)

For tool with locking screw type

wheel guard

Mount the wheel guard with the protrusions on the

wheel guard band aligned with the notches on the bear-

ing box. Then rotate the wheel guard to such an angle

that it can protect the operator according to work. Be

sure to tighten the screw securely.

To remove wheel guard, follow the installation proce-

dure in reverse.

► Fig.5: 1. Wheel guard 2. Bearing box 3. Screw

For tool with clamp lever type wheel

guard

Loosen the screw, and then pull the lever in the direc-

tion of the arrow. Mount the wheel guard with the protru-

sions on the wheel guard band aligned with the notches

on the bearing box. Then rotate the wheel guard to such

an angle that it can protect the operator according to

work.

► Fig.6: 1. Wheel guard 2. Bearing box 3. Screw

4. Lever

Pull the lever in direction of the arrow. Then tighten the

wheel guard with fastening the screw. Be sure to tighten

the screw securely. The setting angle of the wheel

guard can be adjusted with the lever.

► Fig.7: 1. Screw 2. Lever

To remove wheel guard, follow the installation proce-

dure in reverse.

Installing or removing depressed

center wheel or ap disc

Optional accessory

WARNING: When using a depressed center

wheel or ap disc, the wheel guard must be tted

on the tool so that the closed side of the guard

always points toward the operator.

WARNING: Never use a grinding wheel which

is more than 6.5 mm thick.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita GA9063R Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info