Bedienungsanleitung Makita HM1130C (Seite 5 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

599548

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

ENGLISH

Explanation of general view

1 Bit grease

2Bit

3 Tool holder cap

4 Tool holder cover

5 Side handle

6 Can be swung 360° on the

vertical and secured at any

desired position

7 Secures at eight different

positions back and forth

on the horizontal

8 Clamp nut

9 Loosen

10 Tighten

11 “ON I” button

12 ON

13 OFF

14 Adjusting dial

15 Screwdriver

16 Rear cover

17 Screws

18 Brush holder cap

19 Socket wrench

20 Crank cap

21 Hammer grease

SPECIFICATIONS

Model HM1130 HM1130C

Blows per minute ..........................................................................2,650 1,300 – 2,650

Overall length ...............................................................................515 mm 515 mm

Net weight.....................................................................................6.1 kg 6.1 kg

• Due to our continuing programme of research and

development, the specifications herein are subject to

change without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recom-

mended that you wear a dust mask, ear protec-

tors and thickly padded gloves.

2. Be sure the bit is secured in place before opera-

tion.

3. Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

4. In cold weather or when the tool has not been

used for a long time, let the tool warm up for sev-

eral minutes by operating it under no load. This

will loosen up the lubrication. Without proper

warm-up, hammering operation is difficult.

5. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

6. Hold the tool firmly with both hands.

7. Keep hands away from moving parts.

8. Do not leave the tool running. Operate the tool

only when hand-held.

9. Do not point the tool at any one in the area when

operating. The bit could fly out and injure some-

one seriously.

10. When chipping into walls, floors or wherever

“live” electrical wires may be encountered, DO

NOT TOUCH ANY METAL PARTS OF THE TOOL!

Hold the tool by the insulated grasping surfaces to

prevent electric shock if you chip into a “live” wire.

11. Do not touch the bit or parts close to the bit imme-

diately after operation; they may be extremely hot

and could burn your skin.

SAVE THESE INSTRUCTIONS.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HM1130C Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info