Bedienungsanleitung Makita HM1130C (Seite 6 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

599548

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

OPERATING INSTRUCTIONS

Installing or removing bit

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

Clean the bit shank and apply the bit grease provided to

it before installing the bit. (Fig. 1)

Insert the bit into the tool holder cap. (Fig. 2)

If the bit cannot be pushed in, remove the bit. Pull the tool

holder cover down a couple of times. Then insert the bit

again. After installing, always make sure that the bit is

securely held in place by trying to pull it out. (Fig. 3)

To remove the bit, pull the tool holder cover down all the

way and pull the bit out. (Fig. 4)

Side handle (auxiliary handle) (Fig. 5)

The side handle can be swung 360° on the vertical and

secured at any desired position. It also secures at eight

different positions back and forth on the horizontal. Just

loosen the clamp nut to swing the side handle to a

desired position. Then tighten the clamp nut securely.

Switch action (Fig. 6)

CAUTION:

Before plugging in the tool, always check to see that the

tool is switched off.

To start the tool, push the “ON I” button on the left side of

the tool. To stop the tool, push the “OFF O” button on the

right side of the tool.

Speed change (Fig. 7)

For HM1130C only

The blows per minute can be adjusted between 1,300

and 2,650 BPM just by turning the adjusting dial. This

can be done even while the tool is running. The dial is

marked 1 (lowest speed) to 5 (full speed). Refer to the

table below for the relationship between the number set-

tings on the adjusting dial and the blows per minute.

Chipping / Scaling / Demolition (Fig. 8)

Hold the tool firmly with both hands. Turn the tool on and

apply slight pressure on the tool so that the tool will not

bounce around, uncontrolled. Pressing very hard on the

tool will not increase the efficiency.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Replacement of carbon brushes (Fig. 9 & 10)

Whenever carbon brushes must be replaced, they cut out

the tool automatically. When this occurs, loosen the

screws which secure the rear cover. Pry up the rear cover

with a screwdriver and remove it. Then replace both car-

bon brushes at the same time. Use only identical carbon

brushes.

Lubrication (Fig. 11 & 12)

This tool requires no hourly or daily lubrication because it

has a grease-packed lubrication system. Lubricate the

tool every time the carbon brushes are replaced.

Run the tool for several minutes to warm it up. Switch off

and unplug the tool. Remove the crank cap using a

socket wrench. Rest the tool on the table with the bit end

pointing upwards. This will allow the old grease to collect

inside the crank housing. Wipe out the old grease inside

and replace with a fresh grease (30 g). Use only Makita

genuine grease (optional accessory). Filling with more

than the specified amount of grease (approx. 30 g) can

cause faulty hammering action or tool failure. Fill only

with the specified amount of grease. Reinstall the crank

cap and tighten with the socket wrench. Do not tighten

the crank cap excessively. It is made of resin and is sub-

ject to breakage.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Centre.

Number on

adjusting dial

Blows per minute

52,650

42,350

31,950

21,550

11,300

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HM1130C Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info