Bedienungsanleitung Makita HR009G (Seite 17 von 188) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

793650

Zoom out

Zoom in

Vorherige Seite

1/188

Nächste Seite

17 ENGLISH

NOTE: Depending on the conditions of use and the

󰀨

from the actual capacity.

NOTE:

the battery protection system works.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

󰀨

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the battery is operated in a manner that causes

it to draw an abnormally high current, the tool automat-

ically stops without any indication. In this situation, turn

󰀨

to become overloaded. Then turn the tool on to restart.

Overheat protection

When the tool or battery is overheated, the tool stops

automatically. In this case, let the tool and battery cool

before turning the tool on again.

NOTE: When the tool is overheated, the lamp blinks.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically. In this case, remove the battery from the

tool and charge the battery.

Protections against other causes

Protection system is also designed for other causes

that could damage the tool and allows the tool to stop

automatically. Take all the following steps to clear the

causes, when the tool has been brought to a temporary

halt or stop in operation.

 󰀨

restart.

2. Charge the battery(ies) or replace it/them with

recharged battery(ies).

3. Let the tool and battery(ies) cool down.

If no improvement can be found by restoring protection

system, then contact your local Makita Service Center.

Switch action

WARNING: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

Fig.3: 1. Switch trigger

To start the tool, simply pull the switch trigger. Tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

Speed change

The revolutions and blows per minute can be changed



from 1 to 5. Higher speed is obtained when the dial

is turned in the direction of number 5. Lower speed is

obtained when the dial is turned in the direction of num-

ber 1. A target speed can be obtained when the switch

trigger is fully squeezed.

Fig.4: 1.

Refer to the table for the relationship between the num-



revolutions and blows per minute.

Number Revolutions per

minute

Blows per minute

5840 4,500

4760 4,070

3550 2,950

2350 1,880

1300 1,610

CAUTION: Do not turn the adjusting dial when

the tool is running. Failure to do so may result in

the loss of control of the tool and cause an injury.

NOTICE: If the tool is operated continuously at

low speed for a long time, the motor will get over-

loaded, resulting in tool malfunction.

NOTICE: The adjusting dial turns between num-

ber setting 1 and 5. Avoid turning the dial back

and forwards further as it may cause damage to

the tool.

Lighting up the front lamp

Fig.5: 1. Lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The lamp goes out approximately 10 seconds after

releasing the switch trigger.

CAUTION: 󰀨

for a few seconds, the active feedback sensing

technology is not working properly. Ask your

local Makita Service Center for repair.

NOTE:󰀨

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

NOTE: When the tool is overheated, the lamp



then cool down the tool/battery before operating

again.

NOTE: The front lamp cannot be used while the dust

collection system (optional accessory) is installed in

the tool.

Makita HR009G Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info