Bedienungsanleitung Makita HR009G (Seite 19 von 188) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

793650

Zoom out

Zoom in

Vorherige Seite

1/188

Nächste Seite

19 ENGLISH

Connecting lanyard (tether strap) to

the hook

CAUTION: Do not use damaged hook and

screws. Before use, always check for damages,

cracks or deformations, and make sure that the

screws are tightened.

CAUTION: Make sure that the hook is

securely installed with the screws.

CAUTION: Do not install or remove any

accessory while hanging the tool. The tool may fall

if the screws are not tightened.

CAUTION: Always use a locking carabiner

(multi-action and screw gate type) and be sure

to attach the lanyard (tether strap) to the double

looped portion of the hook. Improper attachment

may cause tool drop from the hook and result in



The hook is also used for connecting the lanyard (tether

strap). Be sure to connect the lanyard (tether strap) to

the double looped portion of the hook.

Fig.16: 1. Double looped portion of the hook

2. Lanyard (tether strap) 3. Locking cara-

biner (multi-action and screw gate type)

Safety warnings about connecting

lanyard (tether strap) to the hook



Read all safety warnings and instructions. Failure

to follow the warnings and instructions may result in



1. Always keep the tool tethered when working

"at height". Maximum lanyard length is 2 m.

The maximum permissible fall height for lan-

yard (tether strap) must not exceed 2 m.

2. Use only with lanyards appropriate for this tool

type and rated for at least 10 kg.

3. Do not anchor the tool lanyard to anything on

your body or on movable components. Anchor

the tool lanyard to a rigid structure that can

withstand the forces of a dropped tool.

4. Make sure the lanyard is properly secured at

each end prior to use.

5. Inspect the tool and lanyard before each use

for damage and proper function (including

fabric and stitching). Do not use if damaged or

not functioning properly.

6. Do not wrap lanyards around or allow them to

come in contact with sharp or rough edges.

7. Fasten the other end of the lanyard outside

the working area so that a falling tool is held

securely.

8. Attach the lanyard so that the tool will move

away from the operator if it falls. Dropped tools



or loss of balance.

9. Do not use near moving parts or running

machinery. Failure to do so may result in a crush

or entanglement hazard.

10. Do not carry the tool by the attachment device

or the lanyard.

11. Only transfer the tool between your hands

while you are properly balanced.

12. Do not attach lanyards to the tool in a way that

keeps switches or trigger-lock (if supplied)

from operating properly.

13. Avoid getting tangled in the lanyard.

14. Keep lanyard away from the drilling area of the

tool.

15. Use a locking carabiner (multi-action and

screw gate type). Do not use single action

spring clip carabiners.

16. In the event the tool is dropped, it must be

tagged and removed from service, and should

be inspected by a Makita Factory or Authorized

Service Center.

Accidental restart preventive

function

If you install the battery cartridge while pulling the

switch trigger, the tool does not start. To start the tool,

release the switch trigger, and then pull the switch

trigger.

Torque limiter

NOTICE: As soon as the torque limiter actuates,

󰀨 This will help pre-

vent premature wear of the tool.

NOTICE: Drill bits such as hole saw, which tend

to pinch or catch easily in the hole, are not appro-

priate for this tool. This is because they will cause

the torque limiter to actuate too frequently.

The torque limiter will actuate when a certain torque

level is reached. The motor will disengage from the

output shaft. When this happens, the drill bit will stop

turning.

Electronic function

The tool is equipped with the electronic functions for

easy operation.

• Electric brake

This tool is equipped with an electric brake. If the

tool consistently fails to quickly cease to function

after the switch trigger is released, have the tool

serviced at a Makita service center.

• Constant speed control

The speed control function provides the constant

rotation speed regardless of load conditions.

• Active Feedback sensing Technology

If the tool is swung at the predetermined accelera-

tion during operation, the motor is forcibly stopped

to reduce the burden on the wrist.

NOTE: This function does not work if the acceleration

does not reach the predetermined one when the tool

is swung.

NOTE: If the bit is swung at the predetermined

acceleration during chipping, scaling, or demolishing,

the motor is forcibly stopped. In this case, release

the switch trigger, and then pull the switch trigger to

restart the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR009G Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info