Bedienungsanleitung Makita HR009G (Seite 20 von 188) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

793650

Zoom out

Zoom in

Vorherige Seite

1/188

Nächste Seite

20 ENGLISH

ASSEMBLY

CAUTION: Always be sure that the tool is

󰀨

before carrying out any work on the tool.

Side grip (auxiliary handle)

CAUTION: Always use the side grip to ensure

safe operation.

CAUTION:

After installing or adjusting the side



with its retaining projections fully engaged by the

positioning recesses on the gear housing.

To install the side grip, follow the steps below.

Loosen the thumb screw on the side grip. Then install

the side grip over the barrel neck of the gear housing.

Fig.17: 1. Side grip 2. Thumb screw 3. Barrel neck

of the gear housing 4.

5. Positioning recess

The attachment ring can be enlarged by pressing the

thumb screw down so that the ring is easily and securely

engaged over the barrel neck of the gear housing.

Fig.18: 1. Thumb screw 2. Attachment ring

2. Tighten the thumb screw to secure the grip at your

desired angle.

Installing and removing drill bit

Grease

Clean the shank end of the drill bit and apply grease

before installing the drill bit.

Coat the shank end of the drill bit beforehand with a

small amount of grease (about 0.5 - 1 g).

This chuck lubrication assures smooth action and lon-

ger service life.

Fig.19: 1. Shank end 2. Grease

Place the shank end of the drill bit into the chuck, and

insert it further into the chuck while hand-turning the



becomes fully engaged.

Having installed the drill bit, try pulling it back to ensure

it is securely held in place.

Fig.20: 1. Drill bit 2. Chuck

To remove the drill bit, push the chuck cover down all

the way and pull the drill bit out.

Fig.21: 1. Drill bit 2. Chuck cover

Chisel angle (when chipping,

scaling or demolishing)

The chisel can be secured at the desired angle. To change

the chisel angle, rotate the action mode changing knob to

the O symbol. Turn the chisel to the desired angle.

Fig.22: 1. Action mode changing knob

Rotate the action mode changing knob to the sym-

bol. Then make sure that the chisel is securely held in

place by turning it slightly.

Depth gauge

The depth gauge is convenient for drilling holes of uniform depth.

Press and hold the lock button, and then insert the

depth gauge into the hex hole. Make sure that the

toothed side of the depth gauge faces the marking.

Fig.23: 1. Depth gauge 2. Lock button 3. Marking

4. Toothed side





release the lock button to lock the depth gauge.

NOTE: Make sure that the depth gauge does not

touch the main body of the tool when attaching it.

Dust cup

Optional accessory

Use the dust cup to prevent dust from falling over the tool and

on yourself when performing overhead drilling operations.



of bits which the dust cup can be attached to is as follows.

Model Bit diameter

Dust cup 5 6 mm - 14.5 mm

Dust cup 9 12 mm - 16 mm

Fig.24: 1. Dust cup

Dust cup set

Optional accessory

CAUTION: Before installing and uninstalling

the dust cup set, remove a bit from the tool.

Installation

For model HR008G

1. Attach the spacer to the attachment unit of the

dust cup set aligning the symbol on the attachment

unit with one of the grooves in the spacer.

Fig.25: 1. Spacer 2. Dust cup set 3. Attachment unit

4. symbol 5. Groove

2. Place the dust cup set with the spacer onto the

barrel neck of the gear housing aligning the symbol

on the dust cup set with one of the grooves in the barrel.

Then hold the attachment unit of the dust cup set and

push it down onto the barrel to secure it in place.

Fig.26: 1. Dust cup set 2. Attachment unit 3. Spacer

4. symbol 5. Groove

For model HR009G

Place the dust cup set onto the barrel neck of the gear housing

aligning the symbol on the dust cup set with one of the

grooves in the barrel. Then hold the attachment unit of the dust

cup set and push it down onto the barrel to secure it in place.

Fig.27: 1. Dust cup set 2. Attachment unit

3. symbol 4. Groove

NOTE: If you connect a vacuum cleaner to the dust

cup set, remove the dust cap before connecting it.

Fig.28: 1. Dust cap

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR009G Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info