Bedienungsanleitung Makita HR009G (Seite 22 von 188) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

793650

Zoom out

Zoom in

Vorherige Seite

1/188

Nächste Seite

22 ENGLISH

NOTE: 50,000 mm3 of dust equivalents to drilling 10

holes of ø10 mm and 65 mm depth.

Fig.39: 1. Dust case 2. Dial

Disposing of dust

CAUTION: Always be sure that the tool is

󰀨

before carrying out any work on the tool.

CAUTION: Be sure to wear dust mask when

disposing of dust.

CAUTION: Empty the dust case regularly

before the dust case becomes full. Failure to do so

may decrease the dust collection performance and

cause dust inhalation.

CAUTION: The performance of dust collection







guide. Failure to do so may cause dust inhalation.

1. Remove the dust case while pressing down the

latch lever of the dust case.

Fig.40: 1. Latch lever

2. Lift the lock tab slightly outwards and open the

dust case cover.

Fig.41: 1. Dust case cover 2. Lock tab

3. 

Fig.42

NOTICE: 











1. Remove the dust case while pressing down the

latch lever of the dust case.

Fig.43: 1. Latch Lever

2. Lift the lock tab slightly outwards and open the



Fig.44: 1. Filter cover 2. Lock tab

3. 

Fig.45: 1. Filter 2. Filter case

4. 



5. Close the cover of the dust case, and then attach

the dust case to the dust collection system.

Replacing sealing cap

󰀨

collecting performance. Replace the sealing cap with



with guide notch on the nozzle head.

Fig.46: 1. Sealing cap 2.3. Nozzle

head 4. Guide notch

Storage

NOTICE: When not in use for a certain period of

time, the nozzle guide needs to be extended to

approximately 100 mm from its fully shortened

position. Failing to do so may damage the duct hose

pre-installed in the nozzle guide.

Fig.47:

1.2. Approx. 100 mm

OPERATION

CAUTION: Always use the side grip (auxiliary



and switch handle during operations.

CAUTION: Always make sure that the work-

piece is secured before operation.

CAUTION: Do not pull the tool out forcibly

even the bit gets stuck. Loss of control may

cause injury.

NOTICE: Before using the dust collection sys-

tem with the tool, read the section about the dust

collection system.

NOTE: If the battery cartridge is in low temperature,

the tool’s capability may not be fully obtained. In this

case, warm up the battery cartridge by using the

tool with no load for a while to fully obtain the tool’s

capability.

Fig.48

Hammer drilling operation

CAUTION: There is tremendous and sudden

twisting force exerted on the tool/drill bit at the time of

hole break-through, when the hole becomes clogged

with chips and particles, or when striking reinforcing

rods embedded in the concrete. Always use the side



both side grip and switch handle during opera-

tions. Failure to do so may result in the loss of control



Set the action mode changing knob to the symbol.

Position the drill bit at the desired location for the hole,

then pull the switch trigger.

Apply feed force to the switch handle (main handle) for

󰀩

(auxiliary handle) to keep balance of the tool.

Keep the tool in position and prevent it from slipping

away from the hole.

Do not apply more pressure when the hole becomes

clogged with chips or particles. Instead, run the tool at

an idle, then remove the drill bit partially from the hole.

By repeating this several times, the hole will be cleaned

out and normal drilling may be resumed.

NOTE: Eccentricity in the drill bit rotation may occur

while operating the tool with no load. The tool auto-

matically centers itself during operation. This does not

󰀨

Makita HR009G Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info