Bedienungsanleitung Makita HR166D (Seite 9 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691026

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

9 ENGLISH

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

directionofrotationbeforethetoolstopsmaydam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

Thistoolhasareversingswitchtochangethedirection

ofrotation.Depressthereversingswitchleverfromthe

AsideforclockwiserotationorfromtheBsideforcoun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion,theswitchtriggercannotbepulled.

Selecting the action mode

NOTICE: Do not rotate the action mode chang-

ing knob when the tool is running.Thetoolwillbe

damaged.

NOTICE: To avoid rapid wear on the mode

change mechanism, be sure that the action mode

changing knob is always positively located in one

of the action mode positions.

Rotation with hammering

For drilling in concrete, masonry, etc., rotate the action

modechangingknobtothe symbol.Useacar-

bide-tippeddrillbit.

►Fig.6: 1.Actionmodechangingknob

Rotation only

For drilling in wood, metal or plastic materials, rotate

theactionmodechangingknobtothe symbol.Usea

twistdrillbitorwooddrillbit.

►Fig.7: 1.Actionmodechangingknob

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Side grip (auxiliary handle)

CAUTION: Always use the side grip to ensure

safe operation.

CAUTION: After installing or adjusting the

side grip, make sure that the side grip is rmly

secured.

Installthesidegripsothatthegroovesonthegriptin

theprotrusionsonthetoolbarrel.Turnthegripclock-

wisetosecureit.Thegripcanbexedatdesiredangle.

►Fig.8: 1. Side grip

Grease

Coattheshankendofthedrillbitbeforehandwitha

smallamountofgrease(about0.5-1g).

Thischucklubricationassuressmoothactionandlon-

gerservicelife.

Installing or removing drill bit

Cleantheshankendofthedrillbitandapplygrease

beforeinstallingthedrillbit.

►Fig.9: 1. Shank end 2. Grease

Insertthedrillbitintothetool.Turnthedrillbitandpush

it in until it engages.

Afterinstallingthedrillbit,alwaysmakesurethatthe

drillbitissecurelyheldinplacebytryingtopullitout.

►Fig.10: 1.Drillbit

Toremovethedrillbit,pullthechuckcoverdownallthe

wayandpullthedrillbitout.

►Fig.11: 1.Drillbit2. Chuck cover

Depth gauge

Thedepthgaugeisconvenientfordrillingholesofuniform

depth. Loosen the side grip and insert the depth gauge

intotheholeonthesidegrip.Adjustthedepthgaugeto

thedesireddepthandtightenthesidegriprmly.

►Fig.12: 1. Hole 2. Depth gauge

NOTE:Makesurethatthedepthgaugedoesnot

touchthemainbodyofthetoolwhenattachingit.

Dust cup (optional accessory)

Usethedustcuptopreventdustfromfallingoverthe

toolandonyourselfwhenperformingoverheaddrilling

operations.Attachthedustcuptothebitasshownin

thegure.Thesizeofbitswhichthedustcupcanbe

attachedtoisasfollows.

Model Bit diameter

Dust cup 5 6 mm - 14.5 mm

Dustcup9 12 mm - 16 mm

►Fig.13: 1. Dust cup

Dust cup set (optional accessory)

NOTICE: Do not use the dust cup set when drill-

ing in metal or similar. It may damage the dust cup

setduetotheheatproducedbysmallmetaldustor

similar. Do not install or remove the dust cup set with

thedrillbitinstalledinthetool.Itmaydamagethe

dust cup set and cause dust leak.

NOTE: The standard side grip cannot be used

with the dust cup set being installed on the tool.

Use an optional side grip when the dust cup set is

installed on the tool.

Beforeinstallingthedustcupset,removethebitfrom

thetoolifinstalled.

Installthespacersothatthegroovesonthespacertin

theprotrusionsonthetoolbarrelwhilewideningit.Be

carefulforthespringnottocomeofffromtheslitofspacer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR166D Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info