Bedienungsanleitung Makita HR166D (Seite 10 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691026

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

10 ENGLISH

►Fig.14: 1. Spacer 2. Spring

►Fig.15

Installthesidegripsothatthegrooveonthegriptin

theprotrusiononthespacer.Turnthegripclockwiseto

secure it.

►Fig.16: 1. Side grip

Installthedustcupsetsothattheclawsofthedustcup

tinintheslitsonthespacer.

►Fig.17: 1. Dust cup 2. Claws

NOTE:Ifyouconnectavacuumcleanertothedust

cupset,removethedustcapbeforeconnectingit.

►Fig.18: 1. Dust cap

Toremovethedrillbit,pullthechuckcoverdownallthe

wayandpullthedrillbitout.

►Fig.19: 1. Bit 2. Chuck cover

Toremovethedustcupset,holdtherootofdustcup

and pull it out.

►Fig.20: 1. Dust cup

NOTE:Ifthecapcomesofffromthedustcup,attach

itwithitsprintedsidefacingupsothatgrooveonthe

captsintheinsideperipheryoftheattachment.

►Fig.21

OPERATION

CAUTION: Always use the side grip (auxiliary

handle) and rmly hold the tool by both side grip

and switch handle during operations.

CAUTION: Always make sure that the work-

piece is secured before operation.

NOTE:Ifthebatterycartridgeisinlowtemperature,

thetool’scapabilitymaynotbefullyobtained.Inthis

case,warmupthebatterycartridgebyusingthe

toolwithnoloadforawhiletofullyobtainthetool’s

capability.

►Fig.22

Hammer drilling operation

CAUTION:Thereistremendousandsudden

twistingforceexertedonthetool/drillbitatthetimeof

holebreak-through,whentheholebecomesclogged

withchipsandparticles,orwhenstrikingreinforcing

rodsembeddedintheconcrete.Always use the side

grip (auxiliary handle) and rmly hold the tool by

both side grip and switch handle during opera-

tions.Failuretodosomayresultinthelossofcontrol

ofthetoolandpotentiallysevereinjury.

Settheactionmodechangingknobtothe symbol.

Positionthedrillbitatthedesiredlocationforthehole,

thenpulltheswitchtrigger.Donotforcethetool.Light

pressuregivesbestresults.Keepthetoolinposition

andpreventitfromslippingawayfromthehole.

Donotapplymorepressurewhentheholebecomes

clogged with chips or particles. Instead, run the tool at

anidle,thenremovethedrillbitpartiallyfromthehole.

Byrepeatingthisseveraltimes,theholewillbecleaned

outandnormaldrillingmayberesumed.

NOTE:Eccentricityinthedrillbitrotationmayoccur

whileoperatingthetoolwithnoload.Thetoolauto-

maticallycentersitselfduringoperation.Thisdoesnot

affectthedrillingprecision.

Drilling in wood or metal

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece.Thereisatremendousforceexertedon

thetool/drillbitatthetimeofholebreakthrough.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure workpieces in a

vise or similar hold-down device.

NOTICE: Never use “rotation with hammering”

when the drill chuck is installed on the tool.The

drillchuckmaybedamaged.

Also,thedrillchuckwillcomeoffwhenreversingthe

tool.

NOTICE: Pressing excessively on the tool will

not speed up the drilling.Infact,thisexcessive

pressurewillonlyservetodamagethetipofyourdrill

bit,decreasethetoolperformanceandshortenthe

servicelifeofthetool.

Settheactionmodechangingknobtothe symbol.

Useadrillchuckassembly(optionalaccessory).When

installingit,refertothesection“Installingorremoving

drillbit”.

►Fig.23: 1.Drillchuckassembly

Blow-out bulb (optional accessory)

Afterdrillingthehole,usetheblow-outbulbtocleanthe

dustoutofthehole.

►Fig.24

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

TomaintainproductSAFETYandRELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

beperformedbyMakitaAuthorizedorFactoryService

Centers,alwaysusingMakitareplacementparts.

Makita HR166D Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info