Bedienungsanleitung Makita HR1841F (Seite 8 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691028

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

8 ENGLISH

►Fig.12: 1. Spacer 2. Spring

►Fig.13

Install the side grip (optional grip base set and standard

grip)sothatthegrooveonthegriptintheprotrusion

onthespacer.Turnthegripclockwisetosecureit.

►Fig.14: 1. Side grip

Install the dust cup set so that the claws of the dust cup

tinintheslitsonthespacer.

►Fig.15: 1. Dust cup 2. Claw

NOTE: If you connect a vacuum cleaner to the dust

cup set, remove the dust cap before connecting it.

►Fig.16: 1. Dust cap

Toremovethedrillbit,pullthechuckcoverdownallthe

way and pull the drill bit out.

►Fig.17: 1. Bit 2. Chuck cover

Toremovethedustcupset,holdtherootofdustcup

and pull it out.

►Fig.18

NOTE: If the cap comes off from the dust cup, attach

it with its printed side facing up so that groove on the

captsintheinsideperipheryoftheattachment.

►Fig.19

OPERATION

CAUTION: Always use the side grip (auxiliary

handle) and rmly hold the tool by both side grip

and switch handle during operations.

CAUTION: Always make sure that the work-

piece is secured before operation.

►Fig.20

Hammer drilling operation

CAUTION:Thereistremendousandsudden

twistingforceexertedonthetool/drillbitatthetimeof

hole break-through, when the hole becomes clogged

with chips and particles, or when striking reinforcing

rods embedded in the concrete. Always use the side

grip (auxiliary handle) and rmly hold the tool by

both side grip and switch handle during opera-

tions. Failure to do so may result in the loss of control

ofthetoolandpotentiallysevereinjury.

Set the action mode changing knob to the symbol.

Position the drill bit at the desired location for the hole,

then pull the switch trigger. Do not force the tool. Light

pressure gives best results. Keep the tool in position

and prevent it from slipping away from the hole.

Do not apply more pressure when the hole becomes clogged with

chips or particles. Instead, run the tool at an idle, then remove the

drill bit partially from the hole. By repeating this several times, the

hole will be cleaned out and normal drilling may be resumed.

NOTE: Eccentricity in the drill bit rotation may occur

whileoperatingthetoolwithnoload.Thetoolauto-

maticallycentersitselfduringoperation.Thisdoesnot

affect the drilling precision.

Drilling in wood or metal

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece.Thereisatremendousforceexertedon

the tool/drill bit at the time of hole break through.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure workpieces in a

vise or similar hold-down device.

NOTICE: Never use “rotation with hammering”

when the drill chuck is installed on the tool.The

drill chuck may be damaged.

Also,thedrillchuckwillcomeoffwhenreversingthe

tool.

NOTICE: Pressing excessively on the tool will

not speed up the drilling.Infact,thisexcessive

pressure will only serve to damage the tip of your drill

bit, decrease the tool performance and shorten the

service life of the tool.

Set the action mode changing knob to the symbol.

Attachthechuckadaptertoakeylessdrillchuckto

which1/2"-20sizescrewcanbeinstalled,andthen

install them to the tool. When installing it, refer to the

section “Installing or removing drill bit”.

►Fig.21: 1. Keyless drill chuck 2. Chuck adapter

Blow-out bulb

Optional accessory

Afterdrillingthehole,usetheblow-outbulbtocleanthe

dust out of the hole.

►Fig.22

Using dust cup set

Optional accessory

Fit the dust cup set against the ceiling when operating

the tool.

►Fig.23

NOTICE: Do not use the dust cup set when drill-

ing in metal or similar. It may damage the dust

cup set due to the heat produced by small metal

dust or similar.

NOTICE: Do not install or remove the dust cup

set with the drill bit installed in the tool. It may

damage the dust cup set and cause dust leak.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita HR1841F Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info