Bedienungsanleitung Makita JR105D (Seite 6 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599028

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

6 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipoffyourhands

andresultindamagetothetoolandbatterycartridge

andapersonalinjury.

►Fig.1: 1. Red indicator 2. Button 3. Battery

cartridge

Toremovethebatterycartridge,slideitfromthetool

whileslidingthebuttononthefrontofthecartridge.

Toinstallthebatterycartridge,alignthetongueonthe

batterycartridgewiththegrooveinthehousingandslip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

uppersideofthebutton,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

notbeinginsertedcorrectly.

Battery protection system

Thetoolisequippedwithabatteryprotectionsystem.

Thissystemautomaticallycutsoffpowertothemotorto

extendbatterylife.

Thetoolwillautomaticallystopduringoperationifthe

tooland/orbatteryareplacedunderoneofthefollowing

conditions:

Overloaded:

Thetoolisoperatedinamannerthatcausesittodraw

anabnormallyhighcurrent.

In this situation, release the switch trigger on the tool

andstoptheapplicationthatcausedthetooltobecome

overloaded.Thenpulltheswitchtriggeragaintorestart.

Ifthetooldoesnotstart,thebatteryisoverheated.

Inthissituation,letthebatterycoolbeforepullingthe

switch trigger again.

Low battery voltage:

Theremainingbatterycapacityistoolowandthetool

will not operate. If you pull the switch trigger, the motor

runsagainbutstopssoon.Inthissituation,removeand

rechargethebattery.

Indicating the remaining battery

capacity

Onlyforbatterycartridgeswith"B"attheendofthe

modelnumber

►Fig.2: 1.Indicatorlamps 2.Checkbutton

Pressthecheckbuttononthebatterycartridgetoindi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for few seconds.

Indicator lamps Remaining

capacity

Lighted Off

75% to 100%

50% to 75%

25% to 50%

0% to 25%

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydifferslightly

from the actual capacity.

Switch action

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch lever/trigger actuates properly and returns

to the “OFF” position when released.

►Fig.3: 1.Lock-offbutton  2.Lock-offlever

3. Switch lever 4. Switch trigger

Topreventtheswitchlever/triggerfromaccidentally

pulled,thelock-offlever/buttonareprovided.

Tostartthetool,pulleitherswitchleverortrigger.

• For the switch lever, pull the lock-off lever and

then pull the switch lever to start the tool.

• Fortheswitchtrigger,depressthelock-offbutton

and then pull the switch trigger to start to the tool.

Thelock-offbuttoncanbepressedfromeither

right or left.

Thetoolspeedisincreasedbyincreasingpressureon

theswitchlever/trigger.Releasetheswitchlever/trigger

to stop.

NOTICE:Donotpulltheswitchlever/triggerhard

withoutpullingthelock-offlever/button.Thiscan

causeswitchbreakage.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

►Fig.4: 1. Lamp

Pulltheswitchlever/triggertolightupthelamp.The

lampkeepsonlightingwhiletheswitchlever/triggeris

beingpulled.

Thelampgoesoutapproximately10secondsafter

releasingtheswitchlever/trigger.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JR105D Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita JR105D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info