Bedienungsanleitung Makita JR105D (Seite 7 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

599028

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

7ENGLISH

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

Adjusting the shoe

►Fig.5: 1.Hexwrench  2.Hexbolt 3.Loosen

Whenthebladelosesitscuttingefciencyinoneplace

along its cutting edge, reposition the shoe to utilize a

sharp,unusedportionofitscuttingedge.Thiswillhelp

tolengthenthelifeoftheblade.

Torepositiontheshoe,loosentheboltwithhexwrench.

Slide the shoe to the desired position and then tighten

theboltrmly.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing the recipro/jig

saw blade

CAUTION: Always clean out all chips or foreign

matter adhering to the blade, blade clamp and/or

slider.Failuretodosomaycauseinsufcienttighten-

ingoftheblade,resultinginaseriousinjury.

For Model JR103D

►Fig.6: 1.Reciprosawblade 2.Bladeclampsleeve

Insertthereciprosawbladeintothebladeclampasfar

asitwillgo.Thebladeclampsleeverotatesandxes

thereciprosawblade.Makesurethatthereciprosaw

bladecannotbeextractedeventhoughyoutrytopull

it out.

CAUTION: If you do not insert the recipro saw

blade deep enough, the recipro saw blade may be

ejected unexpectedly during operation.Thiscan

beextremelydangerous.

NOTE:Youcannotusethejigsawbladewith

JR103D.

►Fig.7: 1.Reciprosawblade 2.Bladeclampsleeve

Toremovethereciprosawblade,rotatetheblade

clampsleeveinthedirectionofthearrowfully.Thereci-

prosawbladeisremovedandthebladeclampsleeveis

xedatthereleasedposition.

NOTE:Ifyouremovethereciprosawbladewithout

rotatingthebladeclampsleevefully,thesleeve

maynotbexed.Inthiscase,rotatetheblade

clampsleevefully,thenmakethesleevexedatthe

released position.

For Model JR105D

►Fig.8: 1. Hex wrench 2. Bolt 3. Loosen

4.Tighten

►Fig.9: 1.Reciprosawblade 2.Hexwrench 

3.Holeforreciprosawblade  4.Bladeclamp

Toinstalltherecipro/jigsawblade,loosentheboltby

hexwrench.Wheninstallingareciprosawblade,press

theboltwiththehexwrenchtoopentheslotduring

insertingtheblade.

►Fig.10: 1.Recipro/jigsawblade  2.Bladeclamp

3.Holeforreciprosawblade  4.Holeforjigsaw

blade

►Fig.11

Youcanusebothjigsawblades(Btype)andrecipro

sawbladesaccordingtoyourwork.Inserttherecipro/

jigsawbladestraightintothebladeclampandtighten

itbyhexwrench.Pulltherecipro/jigsawbladelightlyto

makesurethattherecipro/jigsawbladedoesnotfalloff

during operation.

Toremovetherecipro/jigsawblade,followtheinstalla-

tion procedure in reverse.

Hex wrench storage

►Fig.12: 1. Hex wrench 2. Protrusion

When not in use, store the hex wrench as shown in the

guretokeepitfrombeinglost.

OPERATION

CAUTION: Always press the shoe rmly

against the workpiece during operation. If the

shoe is held away from the workpiece during opera-

tion,strongvibrationand/ortwistingwillbeproduced,

causingthebladetosnapdangerously.

CAUTION: Always wear gloves to protect your

hands from hot ying chips when cutting metal.

CAUTION: Be sure to always wear suitable eye

protection which conforms with current national

standards.

CAUTION: Always use a suitable coolant (cut-

ting oil) when cutting metal. Failure to do so will

causeprematurebladewear.

►Fig.13

Presstheshoermlyagainsttheworkpiece.Donot

allowthetooltobounce.Bringthereciprosawblade

into light contact with the workpiece. First, make a pilot

grooveusingaslowerspeed.Thenuseafasterspeed

to continue cutting.

►Fig.14

►Fig.15

You can use the switch lever or trigger according to your

work.

NOTE: If the tool is operated continuously until the

batterycartridgehasdischarged,allowthetooltorest

for15minutesbeforeproceedingwithafreshbattery.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JR105D Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita JR105D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info