Bedienungsanleitung Makita JV101D (Seite 8 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

657989

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

8 ENGLISH

Switch action

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

CAUTION: When not operating the tool,

depress the lock-off button from A side to lock the

switch trigger in the OFF position.

►Fig.4: 1.Lock-offbutton2. Switch trigger

Topreventtheswitchtriggerfromaccidentallypulled,

thelock-offbuttonisprovided.

Tostartthetool,depressthelock-offbuttonfromBside

and pull the switch trigger.

Toolspeedisincreasedbyincreasingpressureonthe

switch trigger. Release the switch trigger to stop. After

use,alwayspressinthelock-offbuttonfromAside.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing jig saw blade

CAUTION: Always clean out all chips or for-

eign matter adhering to the jig saw blade and/or

blade holder.Failuretodosomaycauseinsufcient

tighteningoftheblade,resultinginaseriouspersonal

injury.

CAUTION: Do not touch the jig saw blade or

the workpiece immediately after operation.They

maybeextremelyhotandcouldburnyourskin.

CAUTION: Always secure the jig saw blade

rmly.Insufcienttighteningoftheblademaycause

bladebreakageorseriouspersonalinjury.

CAUTION: Use only B type jig saw blades.

UsingbladesotherthanBtypecausesinsufcient

tighteningoftheblade,resultinginaseriouspersonal

injury.

Toinstallthejigsawblade,loosentheboltcounter-

clockwiseonthejigsawbladeholderwiththehex

wrench.

►Fig.5: 1.Jigsawbladeholder2. Bolt 3. Hex wrench

Withthebladeteethfacingforward,insertthejigsaw

bladeintothejigsawbladeholderasfarasitwillgo.

Makesurethatthebackedgeofthebladetsintothe

roller.Thentightentheboltclockwisetosecurethe

blade.

►Fig.6: 1. Bolt 2. Roller 3.Jigsawblade

Toremovethejigsawblade,followtheinstallation

procedure in reverse.

NOTE:Occasionallylubricatetheroller.

Hex wrench storage

►Fig.7: 1. Hook 2. Hex wrench

When not in use, store the hex wrench as shown in the

guretokeepitfrombeinglost.

First,insertthehexwrenchintothehole.Thenpushit

into the hook until it locked.

Dust cover

CAUTION: Always wear safety goggles even

when operating the tool with the dust cover

lowered.

Lowerthedustcovertopreventchipsfromying.

However,whenmakingbevelcuts,raiseitalltheway.

►Fig.8: 1. Dust cover

OPERATION

CAUTION: Always hold the base ush with

the workpiece.Failuretodosomaycausejigsaw

bladebreakage,resultinginaseriousinjury.

CAUTION: Advance the tool very slowly when

cutting curves or scrolling. Forcing the tool may

causeaslantedcuttingsurfaceandjigsawblade

breakage.

►Fig.9: 1. Cutting line 2. Base

Turnthetoolonwithoutthejigsawblademakingany

contactandwaituntilthebladeattainsfullspeed.Then

restthebaseatontheworkpieceandgentlymovethe

tool forward along the previously marked cutting line.

Bevel cutting

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before tilting the base.

CAUTION: Raise the dust cover all the way

before making bevel cuts.

Withthebasetilted,youcanmakebevelcutsatany

anglebetween0°and45°(leftorright).

►Fig.10

Loosentheboltonthebackofthebasewiththehex

wrench.Movethebasesothattheboltispositionedin

thecenterofthecross-shapedslotinthebase.

►Fig.11: 1. Hex wrench 2. Bolt 3. Base

Tiltthebaseuntilthedesiredbevelangleisobtained.

Theedgeofthemotorhousingindicatesthebevelangle

bygraduations.Thentightenthebolttosecurethebase.

►Fig.12: 1.Edge2. Graduation

Front ush cuts

►Fig.13: 1. Hex wrench 2. Bolt 3. Base

Loosentheboltonthebackofthebasewiththehex

wrenchandslidethebaseallthewayback.Then

tightenthebolttosecurethebase.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JV101D Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info