Bedienungsanleitung Makita JV101D (Seite 9 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

657989

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

9 ENGLISH

Cutouts

Cutoutscanbemadewitheitheroftwomethods

“Boringastartinghole”or“Plungecutting”.

Boring a starting hole

►Fig.14

For internal cutouts without a lead-in cut from an edge,

pre-drill a starting hole 12 mm or more in diameter.

Insertthejigsawbladeintothisholetostartyourcut.

Plunge cutting

►Fig.15

Youneednotboreastartingholeormakealead-incut

if you carefully do as follows.

1. Tiltthetooluponthefrontedgeofthebasewith

thejigsawbladepointpositionedjustabovethework-

piece surface.

2. Apply pressure to the tool so that the front edge of

thebasewillnotmovewhenyouswitchonthetooland

gentlylowerthebackendofthetoolslowly.

3. Asthejigsawbladepiercestheworkpiece,slowly

lowerthebaseofthetooldownontotheworkpiece

surface.

4. Complete the cut in the normal manner.

Finishing edges

►Fig.16

Totrimedgesormakedimensionaladjustments,runthe

jigsawbladelightlyalongthecutedges.

Metal cutting

Alwaysuseasuitablecoolant(cuttingoil)whencutting

metal.Failuretodosowillcausesignicantjigsaw

bladewear.Theundersideoftheworkpiececanbe

greased instead of using a coolant.

Dust extraction

►Fig.17: 1. Hose (optional accessory) 2. Dust cover

Cleancuttingoperationscanbeperformedbyconnect-

ing this tool to a Makita vacuum cleaner.

Insertthehoseofthevacuumcleanerintotheholeat

the rear of the tool.

Lowerthedustcoverbeforeoperation.

NOTE:Dustextractioncannotbeperformedwhen

makingbevelcuts.

Rip fence

Optional accessory

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before installing or removing accessories.

Straight cuts

When repeatedly cutting widths of 160 mm or less, use

of the rip fence will assure fast, clean, straight cuts.

►Fig.18: 1. Rip fence (Guide rule)

Toinstall,inserttheripfenceintotherectangularhole

onthesideofthebasewiththefenceguidefacing

down. Slide the rip fence to the desired cutting width

position,thentightenthebolttosecureit.

►Fig.19: 1. Hex wrench 2. Bolt 3. Fence guide 4. Rip

fence (Guide rule)

Circular cuts

When cutting circles or arcs of 170 mm or less in radius,

install the rip fence as follows.

►Fig.20: 1. Rip fence (Guide rule)

1. Inserttheripfenceintotherectangularholeonthe

sideofthebasewiththefenceguidefacingup.

2. Insertthecircularguidepinthrougheitherofthe

twoholesonthefenceguide.Screwthethreadedknob

onto the pin to secure the pin.

►Fig.21: 1.Threadedknob2. Fence guide 3. Rip

fence (Guide rule) 4.Pin

Slide the rip fence to the desired cutting radius, and tighten

thebolttosecureitinplace.Thenmovethebaseallthewayforward.

NOTE:AlwaysusejigsawbladesNo.B-17,B-18,

B-26 or B-27 when cutting circles or arcs.

Anti-splintering device

Optional accessory, only for aluminum base model

CAUTION: The anti-splintering device cannot

be used when making bevel cuts.

►Fig.22: 1. Base 2. Anti-splintering device

Forsplinter-freecuts,theanti-splinteringdevicecanbe

used.Toinstalltheanti-splinteringdevice,movethetool

baseallthewayforwardandtitfromthebackoftoolbase.

When you use the cover plate, install the anti-splintering

device onto the cover plate.

Cover plate

Optional accessory, only for aluminum base model

►Fig.23: 1. Cover plate 2. Base

Use the cover plate when cutting decorative veneers,

plastics,etc.Itprotectssensitiveordelicatesurfaces

fromdamage.Fititonthebackofthetoolbase.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JV101D Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info