Bedienungsanleitung Makita JV102D (Seite 10 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691877

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

10 ENGLISH

NOTE:Ifthetoolisleftfor10secondswithoutany

operation in the standby mode, the tool automatically

turns off and the lamp goes off.

NOTE: You can also stop and turn off the tool by

pressing the lock/unlock button while the tool is

operating.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

Toturnonthelamp,pressthelock/unlockbutton.To

turn off the lamp, press the lock/unlock button again.

NOTICE: When the tool is overheated, the lamp

ickers. Cool down the tool fully before operating

the tool again.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

Speed adjusting dial

►Fig.5: 1.Speedadjustingdial

Thetoolspeedcanbeadjustedbyturningthespeed

adjustingdial.Youcangetthehighestspeedat5and

the lowest speed at 1.

Refer to the table to select the proper speed for the

workpiece to be cut. However, the appropriate speed

maydifferwiththetypeorthicknessoftheworkpiece.In

general, higher speeds will allow you to cut workpieces

faster but the service life of the blade will be reduced.

Workpiece Number

Wood 4 - 5

Mild steel 3 - 5

Stainless steel 3 - 4

Aluminum 3 - 5

Plastics 1 - 4

NOTICE: When changing the speed dial from "5"

to "1", turn the dial counterclockwise. Do not turn

the dial clockwise forcibly.

Electronic function

Thetoolisequippedwiththeelectronicfunctionsfor

easy operation.

• Softstart

Thesoft-startfunctionminimizesstart-upshock,

and makes the tool start smoothly.

• Softno-loadrotation

Toreducethevibrationandalignthejigsawblade

with the cutting line easily, the tool automatically

reduces the rotation speed until the tool starts cut-

tingtheworkpiecewhenthespeedadjustingdial

is set at 2 or higher. Once the tool starts cutting

the workpiece, the tool speed reaches the preset

speed and keeps the speed until the tool stops.

NOTE: When the temperature is low, this function

may not be available.

Disabling the soft no-load rotation

function

Todisablethesoftno-loadrotationfunction,followthe

steps below.

1. Make sure that the tool is turned off.

2. Setthespeedadjustingdialto"1".

3. Press the lock/unlock button to turn on the tool.

4. Setthespeedadjustingdialto"5"byturningit,

andthensetitto"1"byturnitback.

Thelampblinkstwicetoindicatethatthesoftno-load

rotationfunctionisdisabled.Toenablethisfunction

again, perform the same procedure again.

NOTE:Ifthesoftno-loadrotationfunctionisdisabled,

the lamp blinks twice when the tool is turned on.

NOTE: You can also disable or enable the soft

no-load rotation function by changing the speed

adjustingdialfrom"5"to"1"andchangingitfrom"1"

to"5".

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing jig saw blade

CAUTION: Always clean out all chips or for-

eign matter adhering to the jig saw blade and/or

blade holder.Failuretodosomaycauseinsufcient

tightening of the blade, resulting in a serious personal

injury.

CAUTION: Do not touch the jig saw blade or

the workpiece immediately after operation.They

may be extremely hot and could burn your skin.

CAUTION: Always secure the jig saw blade

rmly.Insufcienttighteningoftheblademaycause

bladebreakageorseriouspersonalinjury.

CAUTION: Use only B type jig saw blades.

UsingbladesotherthanBtypecausesinsufcient

tightening of the blade, resulting in a serious personal

injury.

CAUTION: When you remove the jig saw

blade, be careful not to hurt your ngers with the

top of the blade or the tips of workpiece.

Beforeinstallingthejigsawblade,makesurethatthe

blade clamp lever is in the released position.

Toinstallthejigsawblade,inserttheblade(teethfacing

forward)intothebladeholder.Thelevermovestothe

xedpositionandthebladeislocked.Makesurethat

thebackedgeofthebladetsintotheroller.Pullthe

blade lightly to make sure that the blade does not fall off

during operation.

►Fig.6: 1. Jig saw blade holder 2. Released position

3. Fixed position

►Fig.7: 1. Jig saw blade holder 2. Jig saw blade

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JV102D Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info