Bedienungsanleitung Makita JV102D (Seite 11 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691877

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

11 ENGLISH

CAUTION:Iftheleverdoesnotmovetothexed

position, the blade is not installed completely. Do not

presstheleverbyhandtothexedposition.Itmay

damage the tool.

Toremovethejigsawblade,pushtheleverforwardas

farasitwillgo.Thisallowsthebladetobereleased.

►Fig.8: 1. Jig saw blade holder 2. Jig saw blade

NOTE: Occasionally lubricate the roller.

Hex wrench storage

►Fig.9: 1. Hook 2. Hex wrench

When not in use, store the hex wrench as shown in the

guretokeepitfrombeinglost.

First,insertthehexwrenchintothehole.Thenpushit

into the hook until it locked.

OPERATION

CAUTION: Always hold the base ush with

the workpiece.Failuretodosomaycausejigsaw

bladebreakage,resultinginaseriousinjury.

CAUTION: Advance the tool very slowly when

cutting curves or scrolling. Forcing the tool may

causeaslantedcuttingsurfaceandjigsawblade

breakage.

►Fig.10: 1. Cutting line 2. Base

Turnthetoolonwithoutthejigsawblademakingany

contactandwaituntilthebladeattainsfullspeed.Then

restthebaseatontheworkpieceandgentlymovethe

tool forward along the previously marked cutting line.

Bevel cutting

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before tilting the base.

With the base tilted, you can make bevel cuts at any

anglebetween0°and45°(leftorright).

►Fig.11

Loosen the bolt on the back of the base with the hex

wrench. Move the base so that the bolt is positioned in

the center of the cross-shaped slot in the base.

►Fig.12: 1. Hex wrench 2. Bolt 3. Base

Tiltthebaseuntilthedesiredbevelangleisobtained.

Theedgeofthemotorhousingindicatesthebevel

anglebygraduations.Thentightenthebolttosecure

the base.

►Fig.13: 1. Edge 2. Graduation

Front ush cuts

►Fig.14: 1. Hex wrench 2. Bolt 3. Base

Loosen the bolt on the back of the base with the hex

wrenchandslidethebaseallthewayback.Then

tighten the bolt to secure the base.

Cutouts

Cutouts can be made with either of two methods

“Boring a starting hole” or “Plunge cutting”.

Boring a starting hole

►Fig.15

For internal cutouts without a lead-in cut from an edge,

pre-drill a starting hole 12 mm or more in diameter.

Insertthejigsawbladeintothisholetostartyourcut.

Plunge cutting

►Fig.16

You need not bore a starting hole or make a lead-in cut

if you carefully do as follows.

Tiltthetooluponthefrontedgeofthebasewiththejig

sawbladepointpositionedjustabovetheworkpiecesurface.

2. Apply pressure to the tool so that the front edge of

the base will not move when you switch on the tool and

gently lower the back end of the tool slowly.

Asthejigsawbladepiercestheworkpiece,slowly

lower the base of the tool down onto the workpiece surface.

4. Complete the cut in the normal manner.

Finishing edges

►Fig.17

Totrimedgesormakedimensionaladjustments,runthe

jigsawbladelightlyalongthecutedges.

Metal cutting

Alwaysuseasuitablecoolant(cuttingoil)whencutting

metal.Failuretodosowillcausesignicantjigsaw

bladewear.Theundersideoftheworkpiececanbe

greased instead of using a coolant.

Dust extraction

Clean cutting operations can be performed by connect-

ing this tool to a Makita vacuum cleaner.

Installing or removing the dust cover

Installthedustcoverasshowninthegure.

►Fig.18: 1. Dust cover

Toremovethedustcover,pressonesideofthecover,

andthenremoveitasshowninthegure.

►Fig.19: 1. Dust cover

Installing or removing the dust nozzle

Insertthedustnozzleallthewayintothetool.

►Fig.20: 1. Dust nozzle

Toremovethedustnozzle,pulloutthedustnozzle

while pressing the button on the dust nozzle.

►Fig.21: 1. Button 2. Dust nozzle

Connecting the tool to the vacuum cleaner

Connect the hose of the vacuum cleaner to the dust

nozzle.

►Fig.22

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita JV102D Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info