Bedienungsanleitung Makita LC 1230 (Seite 10 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448572

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Installing or removing saw blade

CAUTION:

• When mounting the blade, make sure that the direction

of the arrow on the surface of the blade matches the

direction of the arrow on the blade case.

• Use only the Makita socket wrench provided to install

or remove the blade. Failure to do so may result in

overtightening or insufficient tightening of the hex bolt.

This could cause a personal injury.

• Do not touch the blade immediately after operation; it

may be extremely hot and could burn your skin.

To remove the blade, use the socket wrench to loosen

the hex bolt holding the center cover by turning it coun-

terclockwise. Raise the blade guard and center cover.

(Fig. 8)

Press the shaft lock to lock the spindle and use the

socket wrench to loosen the hex bolt by turning counter-

clockwise. Then remove the hex bolt, outer flange and

blade. (Fig. 9)

To install the blade, mount the inner flange, saw blade,

outer flange and hex bolt onto the spindle in that order.

Tighten the hex bolt by turning clockwise while pressing

the shaft lock. Return the blade guard and center cover

to its original position. Then tighten the hex bolt clock-

wise to secure the center cover. Lower the handle to

make sure that the blade guard moves properly. (Fig. 10)

Securing workpieces

CAUTION:

• Always set the vise nut to the right fully when securing

the workpiece. Failure to do so may result in insufficient

securing of the workpiece. This could cause the work-

piece to be ejected or cause damage to the blade.

By turning the vise handle counterclockwise and then

flipping the vise nut to the left, the vise is released from

the shaft threads and can be moved rapidly in and out. To

grip workpieces, push the vise handle until the vise plate

contacts the workpiece. Flip the vise nut to the right and

then turn the vise handle clockwise to securely retain the

workpiece. (Fig. 11)

Long workpieces must be supported by blocks of non-

flammable material on either side so that it will be level

with the base top. (Fig. 12)

OPERATION

Cutting operation

CAUTION:

• Never attempt to cut workpieces less than 2 mm thick except pipe or workpieces which cannot be secured firmly with

the vise. The piece cut off may be caught by the blade, causing dangerous scattering of chips and/or damage to the

carbide-tips. Possible serious injury may result.

• Do not apply excessive pressure on the handle when cutting. Too much pressure may result in overload of the motor,

decreased cutting efficiency and/or damage to the carbide-tips or blade itself.

• Too little pressure on the handle may result in more sparks and premature blade wear.

• Do not touch the blade, workpiece or cutting chips immediately after operation; they may be extremely hot and could

burn your skin.

• If the blade stops during operation, makes an odd noise or begins to vibrate, switch off the tool immediately. Replace

cracked or damaged blade with a new one.

• Do not cut aluminum, wood, plastics, concrete, tiles, etc.

• Always use carbide-tipped saw blades appropriate for your job. The use of inappropriate saw blades may cause a

poor cutting performance and/or present a risk of personal injury.

Recommended Carbide-tipped saw blade & workpiece ranges

(NA ... Not applicable)

• Standard blade may differ from country to country.

• Carbide-tipped saw blades for metal cutting saw are not to be re-sharpened.

Diameter &

number of

teeth

Application

Applicable workpiece & thickness range

Angles Pipes Channels

Stainless

Pipes

Stainless

Angles

305 * 60 Mild Steel 4 mm or more 3 – 5 mm 4 mm or more NA NA

305 * 60

Mild Steel

(Lessened

Noise Type)

4 mm or more 3 – 5 mm 4 mm or more NA NA

305 * 78

Thin Mild

Steel

3–6mm 1.2–5mm 2mm or more NA NA

305 * 78

Stainless

Steel

3–6mm 1.2–5mm 4mm or more 1.2–5mm 3–4mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LC 1230 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita LC 1230

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info