Bedienungsanleitung Makita LH 1040 (Seite 14 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448578

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENE060-1

Intended use

The tool is intended for accurate straight cutting and

(only when used as a miter saw on the lower table) miter

cutting in wood.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future reference.

ENB088-5

TABLE TOP MITER SAW SAFETY WARNINGS

FOR BOTH MITER SAW MODE AND TABLE SAW

(BENCH SAW) MODE

1. Check the blade carefully for cracks or deforma-

tion before operation.

Replace damaged blade immediately.

2. Do not operate saw without guards and riving

knife in place, especially after a mode change.

Check blade guards for proper closing before

each use. Do not operate saw if blade guards do

not move freely and close instantly. Never clamp

or tie the blade guards into the open position.

Any irregular operation of the blade guards

should be corrected immediately.

3. Use only saw blades specified by the manufac-

turer and which conform to EN847-1. The groove

width of the cut must be thicker than the riving

knife and the blade body must be thinner than

the riving knife.

4. Do not use saw blades manufactured from high

speed steel.

5. Wear eye protection.

6. Wear hearing protection to reduce the risk of

hearing loss.

7. Wear gloves for handling saw blades (saw

blades shall be carried in a holder wherever

practicable) and rough material.

8. Connect the tool to a dust collecting device

when sawing.

9. Always store the push-stick when it is not in use.

10. Keep the floor area around the tool level well

maintained and free of loose materials e.g. chips

and cut-offs.

11. The operator is adequately trained in the use,

adjustment and operation of the tool.

12. Stop and unplug the saw when unattended.

13. To reduce the emitted noise, always be sure that

the blade is sharp and clean.

14. Use only saw blades that are marked with a max-

imum speed equal to or higher than the no load

speed marked on the tool.

15. When the tool is fitted with a laser or LED, do not

replace the laser or LED with a different type.

Ask an authorized service center for repair.

16. Never remove any cut-offs or other parts of the

workpiece from the cutting area whilst the tool is

running with an unguarded saw blade.

17. The tool should not be used for slotting, rebating

or grooving.

18. Before carrying the tool, always cover the upper

part of the saw blade by the top guard and

secure all moving portions. When lifting or car-

rying the tool, do not use the guard as a carrying

handle.

19. Clean and be careful not to damage the spindle,

flanges (especially the installing surface) and

hex bolt before or when installing the blade.

Damage to these parts could result in blade

breakage. Poor installation may cause vibration/

wobbling or slippage of the blade. Use only

flanges specified for this tool.

20. Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive cut-off wheels may cause an injury.

21. Select the correct saw blade for the material to

be cut.

22. Do not cut metal objects such as nails and

screws. Inspect for and remove all nails, screws

and other foreign material from the workpiece

before operation.

23. Knock out any loose knots from workpiece

BEFORE beginning to cut.

24. Do not use the tool in the presence of flammable

liquids or gases.

25. For your safety, remove the chips, small pieces,

etc. from the work area and table top before

plugging the tool and starting operation.

26. Keep hands and make your bystander and your-

self position out of path of and not in line with

saw blade. Avoid contact with any coasting

blade. It can still cause severe injury and never

reach around saw blade.

27. Be alert at all times, especially during repetitive,

monotonous operations. Do not be lulled into a

false sense of security. Blades are extremely

unforgiving.

28. Make sure the shaft lock is released before the

switch is turned on.

29. Before using the tool on an actual workpiece, let

it run for a while. Watch for vibration or wobbling

that could indicate poor installation or a poorly

balanced blade.

30. Wait until the blade attains full speed before cut-

ting.

31. Stop operation immediately if you notice any-

thing abnormal.

32. Turn off tool and wait for saw blade to stop

before moving workpiece or changing settings.

33. Unplug tool before changing blade, servicing or

not in use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LH 1040 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita LH 1040

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info