Bedienungsanleitung Makita LH 1040 (Seite 15 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448578

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

34. Some dust created from operation contains

chemicals known to cause cancer, birth defects

or other reproductive harm. Some examples of

these chemicals are:

- lead from lead-based-painted material and,

- arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depend-

ing on how often you do this type of work. To

reduce your exposure to these chemicals: work

in a well ventilated area and work with approved

safety equipment, such as those dust masks

that are specially designed to filter out micro-

scopic particles.

35. Even when the tool is used as prescribed it is

not possible to eliminate all residual risk factors.

The following hazards may arise in connection

with the tool’s construction and design:

- Damage to health resulting from hand-arm

vibrations if the power tool is used over a

longer period of time and is not operated or

serviced correctly.

- Injury or damage caused by loose tool attach-

ments which can unexpectedly slide out/from

the power tool due to sudden damage, wear or

improper mounting.

WHEN USING IN MITER SAW MODE:

36. Replace the kerf board when worn.

37. Use a push stick or a push block to avoid work-

ing with the hands and fingers close to the saw

blade.

38. Make sure that the arm is securely fixed when

beveling. Tighten the lever clockwise to fix the

arm.

39. Do not perform any operation freehand. The

workpiece must be secured firmly against the turn

base and guide fence with the vise during all opera-

tions. Never use your hand to secure the workpiece.

40. Ensure that the tool is stable before each cut.

41. Fix the tool to a work bench, if needed.

42. Support long workpieces with appropriate addi-

tional supports.

43. Never cut so small workpiece which cannot be

securely held by the vise. Improperly held work-

piece may cause kickback and serious personal

injury.

44. Do not use the saw to cut other than wood, alu-

minum or similar materials.

45. Make sure that the turn base is properly secured

so it will not move during operation.

46. Make sure the blade does not contact the turn

base in the lowest position and is not contacting

the workpiece before the switch is turned on.

47. Hold the handle firmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

WHEN USING IN THE TABLE SAW (BENCH SAW)

MODE:

48. Make sure that the arm is securely fixed in the

working position. Tighten the lever clockwise to

fix the arm.

49. Make sure that the bench saw table is securely

fixed at the chosen height.

50. Do not perform any operation freehand. Free-

hand means using your hands to support or

guide the workpiece, in lieu of a rip fence.

51. Make sure the blade is not contacting the riving

knife or workpiece before the switch is turned

on.

52. Pay particular attention to instructions for reduc-

ing risk of KICKBACK. KICKBACK is a sudden

reaction to a pinched, bound or misaligned saw

blade. KICKBACK causes the ejection of the

workpiece from the tool back towards the opera-

tor. KICKBACKS CAN LEAD TO SERIOUS PER-

SONAL INJURY. Avoid KICKBACKS by keeping

the blade sharp, by keeping the rip fence parallel

to the blade, by keeping the riving knife and

blade guard in place and operating properly, by

not releasing the workpiece until you have

pushed it all the way past the blade, and by not

ripping a workpiece that is twisted or warped or

does not have a straight edge to guide along the

fence.

53. Avoid abrupt, fast feeding. Feed as slowly as

possible when cutting hard workpieces. Do not

bend or twist workpiece while feeding. If you

stall or jam the blade in the workpiece, turn the

tool off immediately. Unplug the tool. Then clear

the jam.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this instruc-

tion manual may cause serious personal injury.

INSTALLATION

CAUTION:

• Keep the floor area around the tool level well main-

tained and free of loose materials such as chips and

cut-offs.

Installing auxiliary plate (Fig. 1 & 2)

Always install the auxiliary plate using the notch in the

tool’s base and secure it by tightening the hex bolt before

operation.

For European countries

Installing the holders (Fig. 3 & 4)

Install the holders on both sides of the base and secure

them with screws.

Adjust the adjusters so that they contact the floor surface.

Bench mounting (Fig. 5)

This tool should be bolted with two bolts to a level and

stable surface using the bolt holes provided in the tool’s

base. This will help prevent tipping and possible injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Blade guard (Fig. 6 & 7)

CAUTION:

• Make sure that the handle cannot be lowered without

pushing the lever nearby the handle to the left.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LH 1040 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita LH 1040

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info