Bedienungsanleitung Makita LS 1018 (Seite 19 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448595

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

In the case of left bevel cut

Table (A)

Table (B)

Example:

In the case of cutting 52/38° type crown molding for

position (1) in Fig. A:

• Tilt and secure bevel angle setting to 33.9° LEFT.

• Adjust and secure miter angle setting to 31.6°

RIGHT.

• Lay crown molding with its broad back (hidden)

surface down on the turn base with its CEILING

CONTACT EDGE against the guide fence on the

saw.

• The finished piece to be used will always be on the

LEFT side of the blade after the cut has been

made.

In the case of right bevel cut

Table (A)

Table (B)

Example:

In the case of cutting 52/38° type crown molding for

position (1) in Fig. A:

• Tilt and secure bevel angle setting to 33.9° RIGHT.

• Adjust and secure miter angle setting to 31.6°

RIGHT.

• Lay crown molding with its broad back (hidden)

surface down on the turn base with its WALL

CONTACT EDGE against the guide fence on the

saw.

• The finished piece to be used will always be on the

RIGHT side of the blade after the cut has been

made.

7. Cutting aluminum extrusion (Fig. 44 & 45)

When securing aluminum extrusions, use spacer

blocks or pieces of scrap as shown in the figure to

prevent deformation of the aluminum. Use a cutting

lubricant when cutting the aluminum extrusion to

prevent build-up of the aluminum material on the

blade.

WARNING:

• Never attempt to cut thick or round aluminum

extrusions. Thick or round aluminum extrusions can

be difficult to secure and may work loose during the

cutting operation which may result in loss of control and

serious personal injury.

8. Wood facing

Use of wood facing helps to assure splinter-free cuts

in workpieces. Attach a wood facing to the guide fence

using the holes in the guide fence.

See the figure concerning the dimensions for a

suggested wood facing. (Fig. 46)

CAUTION:

• Use straight wood of even thickness as the wood

facing.

WARNING:

• Use screws to attach the wood facing to the guide

fence. The screws should be installed so that the

screw heads are below the surface of the wood

facing so that they will not interfere with the

positioning of the material being cut. Misalignment

of the material being cut can case unexpected

movement during the cutting operation which may

result in a loss of control and serious personal injury.

NOTICE:

• When the wood facing is attached, do not turn the turn

base with the handle lowered. The blade and/or the

wood facing will be damaged.

9. Groove cutting (Fig. 47)

A dado type cut can be made by proceeding as

follows:

Adjust the lower limit position of the blade using the

adjusting screw and the stopper arm to limit the cutting

depth of the blade. Refer to “Stopper arm” section

described previously.

After adjusting the lower limit position of the blade, cut

parallel grooves across the width of the workpiece

using a slide (push) cut as shown in the figure. Then

remove the workpiece material between the grooves

with a chisel.

WARNING:

• Do not attempt to perform this type of cut by using

a wider type blade or dado blade. Attempting to

make a groove cut with a wider blade or dado blade

could lead to unexpected cutting results and kickback

which may result in serious personal injury.

Molding

position in

Fig. A

Bevel angle Miter angle

52/38° type 45° type 52/38° type 45° type

For inside

corner

(1)

Left 33.9° Left 30°

Right 31.6° Right 35.3°

(2)

Left 31.6° Left 35.3°

For outside

corner

(3)

(4) Right 31.6° Right 35.3°

Molding

position in

Fig. A

Molding edge against

guide fence

Finished piece

For inside

corner

(1)

Ceiling contact edge

should be against guide

fence.

Finished piece will be on

the Left side of blade.

(2)

Wall contact edge should

be against guide fence.

For outside

corner

(3)

Finished piece will be on

the Right side of blade.

(4)

Ceiling contact edge

should be against guide

fence.

Molding

position in

Fig. A

Bevel angle Miter angle

52/38° type 45° type 52/38° type 45° type

For inside

corner

(1)

Right 33.9° Right 30°

Right 31.6° Right 35.3°

(2)

Left 31.6° Left 35.3°

For outside

corner

(3)

(4) Right 31.6° Right 35.3°

Molding

position in

Fig. A

Molding edge against

guide fence

Finished piece

For inside

corner

(1)

Wall contact edge should

be against guide fence.

Finished piece will be on

the Right side of blade.

(2) Ceiling contact edge

should be against guide

fence.

For outside

corner

(3)

Finished piece will be on

the Left side of blade.

(4)

Wall contact edge should

be against guide fence.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS 1018 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info