Bedienungsanleitung Makita LS 1018 (Seite 20 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448595

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

• Be sure to return the stopper arm to the original

position when performing other than groove

cutting. Attempting to make cuts with the stopper arm

in the incorrect position could lead to unexpected

cutting results and kickback which may result in serious

personal injury.

CAUTION:

• Be sure to return the stopper arm to the original

position when performing other than groove cutting.

Carrying tool (Fig. 48)

Make sure that the tool is unplugged. Secure the blade at

0° bevel angle and the turn base at the full right miter

angle position. Secure the slide poles so that the lower

slide pole is locked in the position of the carriage fully

pulled to operator and the upper poles are locked in the

position of the carriage fully pushed forward to the guide

fence (refer to the section titled “Slide lock adjustment”.)

Lower the handle fully and lock it in the lowered position

by pushing in the stopper pin.

Wind the power supply cord using the cord rests.

WARNING:

• Stopper pin is only for carrying and storage

purposes and should never be used for any cutting

operations. The use of the stopper pin for cutting

operations may cause unexpected movement of the

saw blade resulting in kickback and serious personal

injury.

Carry the tool by holding both sides of the tool base as

shown in the figure. If you remove the holders, dust bag,

etc., you can carry the tool more easily.

CAUTION:

• Always secure all moving portions before carrying the

tool. If portions of the tool move or slide while being

carried loss of control or balance may occur resulting in

personal injury.

MAINTENANCE

WARNING:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection

or maintenance. Failure to unplug and switch off the

tool may result in accidental start up of the tool which

may result in serious personal injury.

• Always be sure that the blade is sharp and clean

for the best and safest performance. Attempting a

cut with a dull and /or dirty blade may cause kickback

and result in a serious personal injury.

NOTICE:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

1. Miter angle (Fig. 49)

Push the carriage toward the guide fence and tighten

the locking screw to secure the carriage.

Loosen the grip which secures the turn base. Turn the

turn base so that the pointer points to 0° on the miter

scale. Then turn the turn base slightly clockwise and

counterclockwise to seat the turn base in the 0° miter

notch. (Leave as it is if the pointer does not point to

0°.) Loosen the hex sockets bolts securing the guide

fence using the socket wrench. (Fig. 50)

Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin. Square the side

of the blade with the face of the guide fence using a

triangular rule, try-square, etc. Then securely tighten

the hex socket bolts on the guide fence in order

starting from the right side. (Fig. 51)

Make sure that the pointer points to 0° on the miter

scale. If the pointer does not point to 0°, loosen the

screw which secures the pointer and adjust the pointer

so that it will point to 0°.

2. Bevel angle

(1) 0° bevel angle (Fig. 52)

Push the carriage toward the guide fence and

tighten the locking screw to secure the carriage.

Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin. Loosen the

lever at the rear of the tool. (Fig. 53)

Turn the hex bolt on the right side of the arm two

or three revolutions counterclockwise to tilt the

blade to the right. (Fig. 54)

Carefully square the side of the blade with the top

surface of the turn base using the triangular rule,

try-square, etc. by turning the hex bolt on the right

side of the arm clockwise. Then tighten the lever

securely. (Fig. 55)

Make sure that the pointer on the arm point to 0°

on the bevel scale on the arm holder. If they do not

point to 0°, loosen the screw which secure the

pointer and adjust it so that it will point to 0°.

(2) 45° bevel angle (Fig. 56)

Adjust the 45° bevel angle only after performing 0°

bevel angle adjustment. To adjust left 45° bevel

angle, loosen the lever and tilt the blade to the left

fully. Make sure that the pointer on the arm points

to 45° on the bevel scale on the arm holder. If the

pointer does not point to 45°, turn the 45° bevel

angle adjusting bolt on the right side of the arm

holder until the pointer points to 45°.

To adjust the right 45° bevel angle, perform the

same procedure as that described above.

(Fig. 57)

Remove and check the carbon brushes regularly. Replace

when they wear down to 3 mm in length. Keep the carbon

brushes clean and free to slip in the holders. Both carbon

brushes should be replaced at the same time. Use only

identical carbon brushes. (Fig. 58)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

After use

• After use, wipe off chips and dust adhering to the tool

with a cloth or the like. Keep the blade guard clean

according to the directions in the previously covered

section titled “Blade guard”. Lubricate the sliding

portions with machine oil to prevent rust.

Makita LS 1018 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info