Bedienungsanleitung Makita LS1440 (Seite 10 von 76) (Deutsch, Englisch, Polnisch)

599005

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

the direction in which the turn base is to be turned. By

turning the vise knob counterclockwise, the screw is

released and the vise shaft can be moved rapidly in and

out. By turning the vise knob clockwise, the screw

remains secured. To grip the workpiece, turn the vise

knob gently clockwise until the projection reaches its

topmost position, then fasten securely. If the vise knob is

forced in or pulled out while being turned clockwise, the

projection may stop at an angle. In this case, turn the vise

knob back counterclockwise until the screw is released,

before turning again gently clockwise.

CAUTION:

• Grip the workpiece only when the projection is at

the topmost position. Failure to do so may result in

insufficient securing of the workpiece. This could

cause the workpiece to be thrown, cause damage

to the blade or cause the loss of control, which can

result in PERSONAL INJURY.

Vertical vise (optional accessory)

Fig.22

Fig.23

The vertical vise can be installed in the position on either

the left or right side of the guide fence. Insert the vise rod

into the hole in the guide fence and tighten the screw to

secure the vise rod.

Position the vise arm according to the thickness and

shape of the workpiece and secure the vise arm by

tightening the screw. If the screw to secure the vise arm

contacts the guide fence, install the screw on the

opposite side of vise arm. Make sure that no part of the

tool contacts the vise when lowering the handle all the

way. If some part contacts the vise, re-position the vise.

Press the workpiece flat against the guide fence and the

turn base. Position the workpiece at the desired cutting

position and secure it firmly by tightening the vise knob.

CAUTION:

• The workpiece must be secured firmly against the

turn base and guide fence with the vise during all

operations.

OPERATION

CAUTION:

• Before use, be sure to release the handle from the

lowered position by turning the handle latch to the

released position.

• Make sure the blade is not contacting the

workpiece, etc. before the switch is turned on.

• Do not apply excessive pressure on the handle

when cutting. Too much force may result in

overload of the motor and/or decreased cutting

efficiency. Push down handle with only as much

force as is necessary for smooth cutting and

without significant decrease in blade speed.

• Gently press down the handle to perform the cut. If

the handle is pressed down with force or if lateral

force is applied, the blade will vibrate and leave a

mark (saw mark) in the workpiece and the precision

of the cut will be impaired.

1. Press cutting

Fig.24

Secure the workpiece with the vise. Switch on the

tool without the blade making any contact and wait

until the blade attains full speed before lowering.

Then gently lower the handle to the fully lowered

position to cut the workpiece. When the cut is

completed, switch off the tool and WAIT UNTIL

THE BLADE HAS COME TO A COMPLETE STOP

before returning the blade to its fully elevated

position.

2. Miter cutting

Refer to the previously covered "Adjusting the miter

angle".

3. Cutting aluminum extrusion

Fig.25

When securing aluminum extrusions, use spacer

blocks or pieces of scrap as shown in the figure to

prevent deformation of the aluminum. Use a cutting

lubricant when cutting the aluminum extrusion to

prevent build-up of the aluminum material on the

blade.

CAUTION:

• Never attempt to cut thick or round aluminum

extrusions. Thick aluminum extrusions may come

loose during operation and round aluminum

extrusions cannot be secured firmly with this tool.

4. Wood facing

Fig.26

Use of wood facing helps to assure splinter-free

cuts in workpieces. Attach a wood facing to the

guide fence using the holes in the guide fence.

See the figure concerning the dimensions for a

suggested wood facing.

10mm

70mm

150mm

70mm

150mm

45mm

90mm

Over 480mm

012667

CAUTION:

• Use straight wood of even thickness as the wood

facing.

1. Hole

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS1440 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info