Bedienungsanleitung Makita LS1440 (Seite 11 von 76) (Deutsch, Englisch, Polnisch)

599005

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

• Use screws to attach the wood facing to the guide

fence. The screws should be installed so that the

screw heads are below the surface of the wood

facing.

• When the wood facing is attached, do not turn the

turn base with the handle lowered. The blade

and/or the wood facing will be damaged.

NOTE:

• When the wood facing is attached, the maximum

cutting capacities in width will be reduced by

thickness of the wood facing.

5. Cutting repetitive lengths

Fig.27

When cutting several pieces of stock to the same

length, ranging from 300 mm to 400 mm, use of the

set plate (optional accessory) will facilitate more

efficient operation. Install the set plate on the holder

(optional accessory) as shown in the figure.

Align the cutting line on your workpiece with either

the left or right side of the groove in the kerf board,

and while holding the workpiece from moving,

move the set plate flush against the end of the

workpiece. Then secure the set plate with the screw.

When the set plate is not used, loosen the screw

and turn the set plate out of the way.

NOTE:

• Use of the holder-rod assembly (optional

accessory) allows cutting repetitive lengths up to

2,200 mm approximately.

Carrying tool

Fig.28

Make sure that the tool is unplugged. Secure the turn

base at right miter angle fully by means of the grip. Lower

the handle fully and lock it in the lowered position by

turning the handle latch to the locked position.

Carry the tool by holding both sides of the tool base as

shown in the figure. If you remove the holders, dust bag,

etc., you can carry the tool more easily.

Fig.29

CAUTION:

• Always secure all moving portions before carrying

the tool.

• Handle latch is for carrying and storage purposes

only and not for any cutting operations.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection

or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may

result.

WARNING:

• Always be sure that the blade is sharp and clean for

the best and safest performance.

Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

Fig.30

Loosen the grip which secures the turn base. Turn

the turn base so that the pointer points to 0° on the

miter scale. Then turn the turn base slightly

clockwise and counterclockwise to seat the turn

base in the 0° miter notch. (Leave as it is if the

pointer does not point to 0°.) Loosen the hex bolts

securing the guide fence using the socket wrench.

Lower the handle fully and lock it in the lowered

position by turning the handle latch to the locked

position. Square the side of the blade with the face

of the guide fence using a triangular rule, try-square,

etc. Then securely tighten the hex bolts on the

guide fence in the order from the right side.

Fig.31

Make sure that the pointer on the indication plate

points to 0° on the miter scale. If the pointer does

not point to 0°, loosen the screws which secure the

indication plate and adjust it so that the pointer will

point to 0°.

Fig.32

Adjusting for smooth handle action

Fig.33

The hex lock nut which holds the gear housing and the arm

has been factory adjusted to assure smooth handle action

up and down and to guarantee precise cutting. Do not

tamper with it. Should looseness develop at the gear

housing and arm connection, perform the following

adjustment. Work the handle up and down while tightening

the hex lock nut; the best position to tighten the hex lock

nut is just before the motor body weight is obvious.

After adjusting the hex lock nut, be sure that the handle

returns automatically to the initial, raised position from

any position. If the hex lock nut is too loose, the cutting

accuracy will be affected; if it is too tight, it will be hard to

work the handle up and down. Note that this is a self

locking nut. It is a special type that does not loosen in

normal use. It should not be overtightened or replaced

with other types of nuts.

Replacing carbon brushes

Fig.34

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LS1440 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info