Bedienungsanleitung Makita LW1401 (Seite 8 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691733

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

8 ENGLISH

Switch action

WARNING: Before plugging in the tool,

always check to see that the switch trigger actu-

ates properly and returns to the "OFF" position

when released.

►Fig.4: 1.Lockbutton/Lock-offbutton2. Switch

trigger

For tool with lock button

To start the tool, simply pull the switch trigger. Release

theswitchtriggertostop.Forcontinuousoperation,

pulltheswitchtrigger,pushinthelockbuttonandthen

release the switch trigger. To stop the tool from the

locked position, pull the trigger fully, then release it.

CAUTION: Switch can be locked in "ON" posi-

tion for ease of operator comfort during extended

use. Apply caution when locking tool in "ON"

position and maintain rm grasp on tool.

For tool with lock-off button

Topreventtheswitchtriggerfrombeingaccidentally

pulled,alock-offbuttonisprovided.Tostartthetool,

pressthelock-offbuttonandpulltheswitchtrigger.

Release the switch trigger to stop.

WARNING: NEVER defeat the lock-off button

by taping down or some other means. A switch with

anegatedlock-offbuttonmayresultinunintentional

operationandseriouspersonalinjury.

WARNING: NEVER use the tool if it runs when

you simply pull the switch trigger without press-

ing the lock-off button. A switch in need of repair

may result in unintentional operation and serious

personalinjury.ReturntooltoaMakitaservicecenter

forproperrepairsBEFOREfurtherusage.

NOTICE: Do not pull the switch trigger hard

without pressing in the lock-off button. This can

causeswitchbreakage.

Interval between vise and guide

plate

CAUTION: After adjusting the interval

between the vise and the guide plate, make

sure that the guide plate is properly secured.

Insufcientxingmayresultinpersonalinjury.

Thefollowingintervalsettingsoftheviseareavailable:

• 0 - 170 mm (original setting)

• 35 - 205 mm

• 70 - 240 mm

If your work requires different setting, proceed as fol-

lows to change the spacing or interval.

For LW1400

Loosen the screw on the guide plate. Move the guide

plate to the desired position then tighten the screw.

►Fig.5: 1. Screw 2. Guide plate

For LW1401

Removethetwohexboltsusingasocketwrench.Move

the guide plate to the desired position and secure it with

thehexbolts.

►Fig.6: 1. Guide plate 2.Hexbolts

Cutting angle adjustment

CAUTION: After adjusting the angle of the

guide plate, make sure that the guide plate is

properly secured.Insufcientxingmayresultin

personalinjury.

For LW1400

Turn the lever counterclockwise. Move the guide plate

to the desired angle and fully tighten the lever.

►Fig.7: 1. Guide plate 2. Lever

For LW1401

NOTICE: When performing right miter cut,

always set the guide plate at 0 - 170 mm position.

Setting at the 35 - 205 mm or 70 - 240 mm position

hinders the movement of stopper plate, which

results in a failure cut.

Loosenthetwohexboltsusingasocketwrench.Turn

the guide plate to the desired angle and secure it with

thehexbolts.Becarefulnottomovethesetanglewhile

securingthehexbolts.

►Fig.8: 1. Guide plate 2.Hexbolts

NOTE: The scale on the guide plate is only a rough

indication.Formoreaccurateangle,useaprotractor

or triangle ruler. Keep the handle down so that the

cut-offwheelextendsintothebase.Atthesametime,

adjusttheanglebetweentheguideplateandthecut-

off wheel with a protractor or triangle ruler.

Spark guard adjustment

For LW1401 only (country specic)

►Fig.9: 1. Screw 2. Spark guard

The spark guard is factory-installed with its lower edge

contactingthebase.Operatingthetoolinthisposition

willcausemanysparkstoyaround.Loosenthescrew

andadjustthesparkguardtoapositionatwhichmini-

mumsparkswillyaround.

Stopper plate

For LW1401 only (country specic)

►Fig.10: 1. Stopper plate

The stopper plate prevents the cut-off wheel from

contactingtheworkbenchoroor.Whenanewcut-off

wheel is installed, set the stopper plate to position (A).

When the cut-off wheel wears down to the extent that

the lower portion of the workpiece is left uncut, set the

stopper plate to position (B) to allow increased cutting

capacity with a worn down wheel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LW1401 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info