Bedienungsanleitung Makita LW1401 (Seite 9 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691733

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

9 ENGLISH

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

Opening center cap type safety

guard

Country specic

Forthetoolsequippedwithcentercaptypesafetyguard,

loosentheclampingscrewrstthenraisetheguard.

►Fig.11: 1.Clampingscrew

Opening European type safety

guard

Country specic

ForthetoolsequippedwithEuropeantypesafetyguard,

loosentheclampingscrewrstthenopentheguardas

shown.

►Fig.12: 1.Clampingscrew

►Fig.13

►Fig.14

Removing or installing cut-off wheel

CAUTION: Be sure to tighten the toolless

clamp or hex bolt securely.Insufcienttightening

mayresultinsevereinjury.Whentighteningthehex

bolt,usethesocketwrenchprovidedwiththetoolto

assure proper tightening.

CAUTION: Always use only the proper inner

and outer anges which are provided with the

tool.

CAUTION: Always lower the safety guard

after replacing the wheel.

►Fig.15: 1.Innerange2. Ring 3. O-ring 4.Cut-off

wheel 5.Outerange6. Toolless clamp /

Hexbolt

For LW1400

Raise the safety guard. Turn the toolless clamp coun-

terclockwise while holding down the shaft lock. Then

removethetoollessclamp,outerangeandcut-off

wheel. When removing the cut-off wheel, do not remove

theinnerangeaswellastheringandO-ring.

►Fig.16: 1. Shaft lock 2. Toolless clamp

To install the cut-off wheel, follow the removal proce-

duresinreverse.Makesuretottheholeofcut-off

wheel to the ring and return the safety guard.

For LW1401

Raisethesafetyguard.Turnthehexboltcounterclock-

wise using a socket wrench while holding down the shaft

lock.Thenremovethehexbolt,outerangeandwheel.

►Fig.17: 1. Shaft lock 2.Hexbolt

To install the wheel, follow the removal procedures in

reverse.Makesuretottheholeofcut-offwheeltothe

ring and return the safety guard.

OPERATION

CAUTION: Proper handle pressure during

cutting and maximum cutting efciency can

be determined by the amount of sparks that is

produced while cutting. Do not force the cut

by applying excessive pressure on the handle.

Reducedcuttingefciency,prematurewheelwear,as

wellas,possibledamagetothetool,cut-offwheelor

workpiece may result.

Holdthehandlermly.Switchonthetoolandwaituntil

thewheelattainsfullspeedbeforeloweringgently

into the cut. When the wheel contacts the workpiece,

graduallybeardownonthehandletoperformthecut.

When the cut is completed, switch off the tool and wait

until the wheel has come to a complete stop before

returning the handle to the fully elevated position.

Cutting capacity

Maximum cutting capacity varies depending on the

cutting angle and workpiece shape.

Max. cutting capacity with a brand-new cut-off

wheel

Cutting angle /

Workpiece shape

90° 45°

127 mm 127 mm

115 x 130 mm

102 x 194 mm

70 x 233 mm

115 x 103 mm

119 x 119 mm 106 x 106 mm

137 x 137 x 10 mm 100 x 100 x 10 mm

Securing workpiece

CAUTION: Always place the thread holder on

the shaft threads when securing the workpiece.

Failuretodosomayresultininsufcientsecuringof

theworkpiece.Thiscouldcausetheworkpiecetobe

ejectedorcauseadangerousbreakageofthewheel.

Whilethethreadholderislifted,theviseplatecanbe

moved in and out quickly. To grip a workpiece, push the

handle until the vise plate contacts the workpiece then

return the thread holder. Turn the handle clockwise until

the workpiece is securely retained.

►Fig.18: 1. Handle 2. Thread holder 3. Vise plate

Whenthecut-offwheelhasworndownconsiderably,

placeaspacerblockbehindtheworkpieceasshown

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita LW1401 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info