Bedienungsanleitung Makita M2300 (Seite 14 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691825

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

14 ENGLISH

Example:

In the case of cutting 52/38° type crown molding for

position(a)intheabovegure:

• Tilt and secure bevel angle setting to 33.9° LEFT.

• Adjustandsecuremiteranglesettingto31.6°

RIGHT.

• Lay crown molding with its broad back (hidden)

surface down on the turn base with its CEILING

CONTACT EDGE against the guide fence on the

saw.

• Thenishedpiecetobeusedwillalwaysbeon

the LEFT side of the blade after the cut has been

made.

Cutting aluminum extrusion

►Fig.34: 1. Vise 2. Spacer block 3. Guide fence

4. Aluminum extrusion 5. Spacer block

When securing aluminum extrusions, use spacer blocks

orpiecesofscrapasshownintheguretoprevent

deformation of the aluminum. Use a cutting lubricant

when cutting the aluminum extrusion to prevent build-up

of the aluminum material on the blade.

CAUTION: Never attempt to cut thick or round

aluminum extrusions. Thick aluminum extrusions

may come loose during operation and round alumi-

numextrusionscannotbesecuredrmlywiththis

tool.

Wood facing

WARNING: Use screws to attach the wood

facing to the guide fence. The screws should be

installed so that the screw heads are below the

surface of the wood facing so that they will not

interfere with the positioning of the material being

cut. Misalignment of the material being cut can case

unexpected movement during the cutting operation

which may result in a loss of control and serious

personalinjury.

CAUTION: Use the straight wood of even

thickness as the wood facing.

Use of wood facing helps to assure splinter-free cuts

in workpieces. Attach a wood facing to the guide fence

using the holes in the guide fence.

Seethegureconcerningthedimensionsforasug-

gested wood facing.

►Fig.35: 1. Holes

NOTICE: When the wood facing is attached, do

not turn the turn base with the handle lowered.

The blade and/or the wood facing will be damaged.

NOTE: The maximum cutting width will be smaller by

the width of wood facing.

Cutting repetitive lengths

When cutting several pieces of stock to the same

length, ranging from 240 mm to 380 mm, use the set

plate (optional accessory). Install the set plate on the

holder(optionalaccessory)asshowninthegure.

►Fig.36: 1. Set plate 2. Holder 3. Screw

Align the cutting line on your workpiece with either the

left or right side of the groove in the kerf board, and

whileholdingtheworkpiece,movethesetplateush

against the end of the workpiece. Then secure the set

plate with the screw.

When the set plate is not used, loosen the screw and

turn the set plate out of the way.

NOTE: Use of the holder-rod assembly (optional

accessory) allows cutting repetitive lengths up to

2,200 mm approximately.

Carrying tool

►Fig.37: 1. Stopper pin

Make sure that the tool is unplugged. Secure the blade

at 0° bevel angle and the turn base at left miter angle

fully. Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin.

Carrythetoolbycarryinggripasshowninthegure.If

you remove the holders, dust bag, etc., you can carry

the tool more easily.

►Fig.38

CAUTION: Always secure all moving portions

before carrying the tool.

CAUTION: Stopper pin is for carrying and

storage purposes only and not for any cutting

operations.

MAINTENANCE

WARNING: Always be sure that the blade is

sharp and clean for the best and safest perfor-

mance. Attempting a cut with a dull and /or dirty blade

may cause kickback and result in a serious personal

injury.

CAUTION: Always be sure that the tool is

switched off and unplugged before attempting to

perform inspection or maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

Adjusting the cutting angle

Thistooliscarefullyadjustedandalignedatthefactory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

Miter angle

►Fig.39: 1. Hex bolt

Loosen the grip which secures the turn base. Turn the

turn base so that the pointer points to 0° on the miter

scale. Tighten the grip and loosen the hex bolts secur-

ing the guide fence using the wrench. If the pointer

does not point to 0° on the miter scale, loosen the screw

which secures the pointer and move and secure the

pointer plate so that the pointer points to 0° on the miter

scale.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita M2300 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info