Bedienungsanleitung Makita M2300 (Seite 15 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691825

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

15 ENGLISH

Lower the handle fully and lock it in the lowered position

by pushing in the stopper pin. Square the side of the

blade with the face of the guide fence using a triangular

rule, try-square, etc. Then securely tighten the hex bolts

on the guide fence in the order from the right side.

►Fig.40: 1. Triangular rule

Bevel angle

0° bevel angle

►Fig.41: 1.0°bevelangleadjustingbolt

Lower the handle fully and lock it in the lowered position

by pushing in the stopper pin.

Loosen the knob at the rear of the tool.

Loosenthehexnutandturnthe0°bevelangleadjust-

ing bolt on the right side of the turn base two or three

revolutions clockwise to tilt the blade to the right.

Carefully square the side of the blade with the top sur-

face of the turn base using the triangular rule, try-square,

etc.byturningthe0°bevelangleadjustingboltcoun-

terclockwise. Then tighten the hex nut to secure the 0°

bevelangleadjustingboltandtightentheknobsecurely.

Make sure that the pointer on the arm points to 0° on

the bevel scale. If it does not point to 0° on the bevel

scale, loosen the screw which secures the pointer and

move and secure the pointer plate so that the pointer

points to 0° on the bevel scale.

►Fig.42: 1. Triangular rule 2. Saw blade 3. Top sur-

face of turn base

►Fig.43: 1. Pointer

45° bevel angle

►Fig.44: 1.45°bevelangleadjustingbolt2. Pointer

Adjustthe45°bevelangleonlyafterperforming0°

bevelangleadjustment.

Toadjustleft45°bevelangle,loosentheknobandtilt

the blade to the left fully.

Make sure that the pointer on the arm points to 45° on

the bevel scale on the arm.

Ifthepointerdoesnotpointto45°,turnthe45°bevelangleadjust-

ing bolt on the left side of the arm until the pointer points to 45°.

Replacing carbon brushes

►Fig.45

Remove and check the carbon brushes regularly. Replace when

they wear down to 3 mm in length. Keep the carbon brushes

clean and free to slip in the holders. Both carbon brushes should

be replaced at the same time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps.

Take out the worn carbon brushes, insert the new ones

and secure the brush holder caps.

►Fig.46: 1. Brush holder cap 2. Screwdriver

After use

After use, wipe off chips and dust adhering to the tool

with a cloth or the like. Keep the blade guard clean

according to the directions in the previously covered

section titled "Blade guard". Lubricate the sliding por-

tions with machine oil to prevent rust.

To maintain product SAFETY and RELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita M2300 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info